www.GEAppliances.com

WARNING!

For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or loss of life.

ANTI-TIP DEVICE

All ranges can tip and injury could result.

To prevent accidental tipping of the range, attach it to the wall or floor by installing the Anti-Tip device supplied.

If the Anti-Tip device supplied with the range does not fit this application, use the universal Anti-Tip device WB2X7909.

To check if the device is installed and engaged properly, remove the storage drawer and inspect the rear leveling leg. Make sure it fits securely into the slot.

If you pull the range out from the wall for any reason, make sure the device is properly engaged when you push the range back against the wall. If it is not, there is a possible risk of the range tipping over and causing injury if you or a child stand, sit or lean on an open door.

Please refer to the Anti-Tip device information in this manual. Failure to take this precaution could result in tipping of the range and injury.

IMPORTANT SAFETY NOTICE

The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of California to publish a list of substances known to the state to cause birth defects or other reproductive harm, and requires businesses to warn customers of potential exposure to such substances.

Gas appliances can cause minor exposure to four of these substances, namely benzene, carbon monoxide, formaldehyde and soot, caused primarily by the incomplete combustion of natural gas or LP fuels. Properly adjusted burners, indicated by a bluish rather than a yellow flame, will minimize incomplete combustion. Exposure to these substances can be minimized by venting with an open window or using a ventilation fan or hood.

The fiberglass insulation in self-clean ovens gives off a very small amount of carbon monoxide during the cleaning cycle. Exposure can be minimized by venting with an open window or using a ventilation fan or hood.

3

Safety Instructions Operating Instructions Care and Cleaning Troubleshooting Tips Consumer Support

Page 2 Page 4
Page 3
Image 3
GE J2S968 manual Important Safety Notice, All ranges can tip and injury could result
Page 2 Page 4

J2S968 specifications

The GE J2S968 is a high-performance jet engine that has carved a niche for itself in the aviation industry, particularly in corporate and regional jet markets. Designed with the latest technologies, the J2S968 combines efficiency, reliability, and advanced engineering to meet the demands of modern aviation.

One of the standout features of the J2S968 is its turbofan design, which significantly enhances its operational efficiency compared to traditional turbojet engines. The engine employs a wide-chord fan blade technology that not only improves thrust but also minimizes noise levels, adhering to strict environmental regulations. This makes the J2S968 an ideal choice for operators prioritizing sustainability without compromising performance.

Another key characteristic of the J2S968 is its power and thrust capabilities. With a thrust range that typically exceeds 4,000 pounds, this engine can support a variety of aircraft sizes. This engine is particularly favored in the business aviation sector, where performance and range are critical. The advanced materials used in its construction also contribute to weight reduction, further enhancing fuel efficiency and overall performance.

The GE J2S968 incorporates advanced digital engine control systems, which facilitate precise power management and optimize fuel consumption. This technology allows for more efficient operation throughout different phases of flight, translating into reduced operational costs for operators. Enhanced diagnostic capabilities are also a key component, enabling real-time monitoring of engine performance, which aids in maintenance and prolongs service life.

In terms of maintenance, the J2S968 is designed with accessibility in mind. Its modular architecture allows for quick and easy servicing, reducing downtime and ensuring higher aircraft availability. This is particularly important for business aviation where time is often of the essence.

The engine's reliability is further underscored by its track record. Built on GE's extensive experience in the aerospace sector, the J2S968 benefits from rigorous testing and certification processes, ensuring it meets the highest safety and performance standards.

In summary, the GE J2S968 represents a fusion of cutting-edge technology, efficient performance, and reliability. Its significant advancements in turbofan design, power management, and maintenance make it a preferred choice for regional jets and business aircraft. As the aviation industry continues to evolve, the J2S968 stands as a testament to GE's commitment to innovation and excellence in aerospace engineering.
Top Page Image Contents