Care and cleaning of the range.

The gasket is designed with a gap at the bottom to allow for proper air circulation.

Do not rub or clean the door gasket— it has an extremely low resistance to abrasion.

If you notice the gasket becoming worn, frayed or damaged in any way or if it has become displaced on the door, you should have it replaced.

Cleaning the Oven Door

To clean the inside of the door:

■Because the area inside the gasket is cleaned during the self-clean cycle, you do not need to clean this by hand.

■The area outside the gasket and the door liner can be cleaned with a soap-filled or plastic scouring pad, hot water and detergent. Rinse well with a vinegar and water solution.

To clean the outside of the door:

■Use soap and water to thoroughly clean the top, sides and front of the oven door. Rinse well. You may also use a glass cleaner to clean the glass

on the outside of the door. Do not let water drip into the vent openings.

■If any stain on the door vent trim is persistent, use a soft abrasive cleaner and a sponge-scrubber for best results.

■Spillage of marinades, fruit juices, tomato sauces and basting materials containing acids may cause discoloration and should be wiped up immediately. When surface is cool, clean and rinse.

■Do not use oven cleaners, cleaning powders or harsh abrasives on the outside of the door.

Troubleshooting Tips Care and Cleaning Operating Instructions Safety Instructions

Slot

Hinge lock

Pull hinge locks down to unlock.

Removal position

Lift-Off Oven Door

The door is very heavy. Be careful when removing and lifting the door.

Do not lift the door by the handle.

To remove the door:

Fully open the door.

Pull the hinge locks down toward the door frame, to the unlocked position. A tool, such as a small flat-blade screwdriver, may be required.

Firmly grasp both sides of the door at the top.

Close door to the door removal position, which is halfway between the broil stop position and fully closed.

Lift door up and out until the hinge arm is clear of the slot.

To replace the door:

Firmly grasp both sides of the door at the top.

With the

Bottom

Hinge arm

door at the

edge

 

same angle as

of slot

 

the removal

 

 

position, seat the

 

indentation of

 

Indentation

the hinge arm

 

 

 

into the bottom

 

edge of the hinge

 

slot. The notch in the hinge arm

must be fully seated into the bottom

of the slot.

 

 

Fully open the door. If the door will not fully open, the indentation is not seated correctly in the bottom edge of the slot.

Push the hinge locks up against the front frame of the oven cavity to the locked position.

Hinge arm

Hinge lock

Consumer Support

 

 

Push hinge locks up to lock.

 

 

Close the oven door.

 

 

 

 

Painted Surfaces

 

 

Painted surfaces include the top and

Do not use commercial oven cleaners,

 

sides of the door, top of the control panel

cleaning powders, steel wool or harsh

 

and the drawer front. Clean these with

abrasives on any painted surface.

 

soap and water or a vinegar and water

 

 

solution.

 

32

 

Page 31 Page 33
Page 32
Image 32
GE J2S968 manual Cleaning the Oven Door, Lift-Off Oven Door, Painted Surfaces
Page 31 Page 33

J2S968 specifications

The GE J2S968 is a high-performance jet engine that has carved a niche for itself in the aviation industry, particularly in corporate and regional jet markets. Designed with the latest technologies, the J2S968 combines efficiency, reliability, and advanced engineering to meet the demands of modern aviation.

One of the standout features of the J2S968 is its turbofan design, which significantly enhances its operational efficiency compared to traditional turbojet engines. The engine employs a wide-chord fan blade technology that not only improves thrust but also minimizes noise levels, adhering to strict environmental regulations. This makes the J2S968 an ideal choice for operators prioritizing sustainability without compromising performance.

Another key characteristic of the J2S968 is its power and thrust capabilities. With a thrust range that typically exceeds 4,000 pounds, this engine can support a variety of aircraft sizes. This engine is particularly favored in the business aviation sector, where performance and range are critical. The advanced materials used in its construction also contribute to weight reduction, further enhancing fuel efficiency and overall performance.

The GE J2S968 incorporates advanced digital engine control systems, which facilitate precise power management and optimize fuel consumption. This technology allows for more efficient operation throughout different phases of flight, translating into reduced operational costs for operators. Enhanced diagnostic capabilities are also a key component, enabling real-time monitoring of engine performance, which aids in maintenance and prolongs service life.

In terms of maintenance, the J2S968 is designed with accessibility in mind. Its modular architecture allows for quick and easy servicing, reducing downtime and ensuring higher aircraft availability. This is particularly important for business aviation where time is often of the essence.

The engine's reliability is further underscored by its track record. Built on GE's extensive experience in the aerospace sector, the J2S968 benefits from rigorous testing and certification processes, ensuring it meets the highest safety and performance standards.

In summary, the GE J2S968 represents a fusion of cutting-edge technology, efficient performance, and reliability. Its significant advancements in turbofan design, power management, and maintenance make it a preferred choice for regional jets and business aircraft. As the aviation industry continues to evolve, the J2S968 stands as a testament to GE's commitment to innovation and excellence in aerospace engineering.
Top Page Image Contents