Do not leave children alone or unattended where a range is hot or in operation. They could be seriously burned.

Consumer Support Troubleshooting Tips Care and Cleaning Operating Instructions Safety Instructions

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

SAFETY PRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:

Use this appliance only for its intended

Be sure all packaging materials are

purpose as described in this Owner’s

removed from the range before operating

Manual.

it to prevent fire or smoke damage should

Be sure your appliance is properly installed

the packaging material ignite.

 

and grounded by a qualified technician in accordance with the provided installation instructions.

Before performing any service, disconnect

Do not attempt to repair or replace any

the range power supply at the household

part of your range unless it is specifically

distribution panel by removing the fuse or

recommended in this manual. All other

switching off the circuit breaker.

service should be referred to a qualified

Have the installer show you the location of

technician.

 

the circuit breaker or fuse. Mark it for easy

Be sure your range is correctly adjusted

reference.

by a qualified service technician or installer

Do not leave children alone—children

for the type of gas (natural or LP) that is

to be used. Your range can be converted

should not be left alone or unattended in

for use with either type of gas. See the

an area where an appliance is in use. They

Installation Instructions packed with

should never be allowed to sit or stand on

the range.

any part of the appliance.

WARNING: These adjustments

Have the installer show you the location

of the range gas shut-off valve and how to

must be made by a qualified service

shut it off if necessary.

technician in accordance with the

Have your range installed and properly

manufacturer’s instructions and all codes

and requirements of the authority having

grounded by a qualified installer, in

jurisdiction. Failure to follow these

accordance with the Installation

instructions could result in serious injury or

Instructions. Any adjustment and service

property damage. The qualified agency

should be performed only by qualified gas

performing this work assumes

range installers or service technicians.

responsibility for the conversion.

 

Locate the range out of kitchen traffic path and out of drafty locations to prevent poor air circulation.

4

Page 4
Image 4
GE J2S968 manual Manufacturer’s instructions and all codes, Requirements of the authority having

J2S968 specifications

The GE J2S968 is a high-performance jet engine that has carved a niche for itself in the aviation industry, particularly in corporate and regional jet markets. Designed with the latest technologies, the J2S968 combines efficiency, reliability, and advanced engineering to meet the demands of modern aviation.

One of the standout features of the J2S968 is its turbofan design, which significantly enhances its operational efficiency compared to traditional turbojet engines. The engine employs a wide-chord fan blade technology that not only improves thrust but also minimizes noise levels, adhering to strict environmental regulations. This makes the J2S968 an ideal choice for operators prioritizing sustainability without compromising performance.

Another key characteristic of the J2S968 is its power and thrust capabilities. With a thrust range that typically exceeds 4,000 pounds, this engine can support a variety of aircraft sizes. This engine is particularly favored in the business aviation sector, where performance and range are critical. The advanced materials used in its construction also contribute to weight reduction, further enhancing fuel efficiency and overall performance.

The GE J2S968 incorporates advanced digital engine control systems, which facilitate precise power management and optimize fuel consumption. This technology allows for more efficient operation throughout different phases of flight, translating into reduced operational costs for operators. Enhanced diagnostic capabilities are also a key component, enabling real-time monitoring of engine performance, which aids in maintenance and prolongs service life.

In terms of maintenance, the J2S968 is designed with accessibility in mind. Its modular architecture allows for quick and easy servicing, reducing downtime and ensuring higher aircraft availability. This is particularly important for business aviation where time is often of the essence.

The engine's reliability is further underscored by its track record. Built on GE's extensive experience in the aerospace sector, the J2S968 benefits from rigorous testing and certification processes, ensuring it meets the highest safety and performance standards.

In summary, the GE J2S968 represents a fusion of cutting-edge technology, efficient performance, and reliability. Its significant advancements in turbofan design, power management, and maintenance make it a preferred choice for regional jets and business aircraft. As the aviation industry continues to evolve, the J2S968 stands as a testament to GE's commitment to innovation and excellence in aerospace engineering.