www.GEAppliances.com

Safety

Stainless Steel Surfaces

Do not use a steel-wool pad; it will scratch the surface.

Shake bottle well.

Place a small amount of CERAMA BRYTE® Stainless Steel Appliance Cleaner on a damp cloth or damp paper towel.

Clean a small area (approximately 8″ x 8″), rubbing with the grain of the stainless steel if applicable.

Dry and buff with a clean, dry paper towel or soft cloth.

Repeat as necessary.

NOTE: If a mineral oil-based stainless steel appliance cleaner has been used before to clean the appliance, wash the surface with dishwashing liquid and water prior to using the CERAMA BRYTE® Stainless

Steel Appliance Cleaner. After washing the surface with dishwashing liquid and water, use a generous amount of CERAMA BRYTE® Stainless Steel Appliance Cleaner to clean the appliance.

To Order

To order CERAMA BRYTE® Stainless Steel Appliance Cleaner, please call our toll-free number:

National Parts

Center . . . . . . . . . . . .800.626.2002 (U.S.)

888.261.3055 (Canada)

www.GEAppliances.com (U.S.) www.geappliances.ca (Canada)

CERAMA BRYTE®

Stainless Steel Appliance

Cleaner . . . . . . . . . . . . . . . . . . . .# PM10X311

Instructions Operating Instructions Care

Oven Vent

The oven vent is above the left side of the door.

It is normal for steam to come out of

This area could become hot during

the vent.

The vent is important for proper air circulation.

oven use.

 

Never block this vent.

and Cleaning

Control Panel

If desired, the touch pads may be turned off before cleaning.

See the Control Lockout section.

Clean up splatters with a damp cloth.

You may also use a glass cleaner.

Remove heavier soil with warm soapy water. Do not use abrasives of any kind.

Turn on the touch pads after cleaning.

Troubleshooting

Oven Heating Elements

Do not clean the broil element. Any soil

On some models, the bake element is not

will burn off when the element is heated.

exposed and is under the oven floor. If spillovers,

Clean the oven floor with warm, soapy

residue or ash accumulate on the oven floor, wipe

water.

up before self-cleaning.

 

Tips

Press down and pull out.

Removable Oven Floor

To remove the oven floor for easier cleaning:

Remove the oven door using the instructions in the Lift-Off Oven Door section.

Press down and pull out the removable oven floor.

Clean the oven floor with warm soapy water.

When reinstalling the oven floor, be sure to slide it all the way to the back of the oven.

IMPORTANT: Always replace the removable floor before the next use.

33

Consumer Support

Page 33
Image 33
GE J2S968 manual Tips, Instructions Operating Instructions Care, Cleaning

J2S968 specifications

The GE J2S968 is a high-performance jet engine that has carved a niche for itself in the aviation industry, particularly in corporate and regional jet markets. Designed with the latest technologies, the J2S968 combines efficiency, reliability, and advanced engineering to meet the demands of modern aviation.

One of the standout features of the J2S968 is its turbofan design, which significantly enhances its operational efficiency compared to traditional turbojet engines. The engine employs a wide-chord fan blade technology that not only improves thrust but also minimizes noise levels, adhering to strict environmental regulations. This makes the J2S968 an ideal choice for operators prioritizing sustainability without compromising performance.

Another key characteristic of the J2S968 is its power and thrust capabilities. With a thrust range that typically exceeds 4,000 pounds, this engine can support a variety of aircraft sizes. This engine is particularly favored in the business aviation sector, where performance and range are critical. The advanced materials used in its construction also contribute to weight reduction, further enhancing fuel efficiency and overall performance.

The GE J2S968 incorporates advanced digital engine control systems, which facilitate precise power management and optimize fuel consumption. This technology allows for more efficient operation throughout different phases of flight, translating into reduced operational costs for operators. Enhanced diagnostic capabilities are also a key component, enabling real-time monitoring of engine performance, which aids in maintenance and prolongs service life.

In terms of maintenance, the J2S968 is designed with accessibility in mind. Its modular architecture allows for quick and easy servicing, reducing downtime and ensuring higher aircraft availability. This is particularly important for business aviation where time is often of the essence.

The engine's reliability is further underscored by its track record. Built on GE's extensive experience in the aerospace sector, the J2S968 benefits from rigorous testing and certification processes, ensuring it meets the highest safety and performance standards.

In summary, the GE J2S968 represents a fusion of cutting-edge technology, efficient performance, and reliability. Its significant advancements in turbofan design, power management, and maintenance make it a preferred choice for regional jets and business aircraft. As the aviation industry continues to evolve, the J2S968 stands as a testament to GE's commitment to innovation and excellence in aerospace engineering.