Instructions

Using the gas surface burners.

Throughout this manual, features and appearance may vary from your model.

Instructions Safety

Push the control knob in and turn it to the LITE position.

How to Light a Gas Surface Burner

Push the control knob in and turn it to the LITE position.

You will hear a little clicking noise— the sound of the electric spark igniting the burner.

After the flame lights, turn the knob to adjust the flame size. If the knob stays at LITE, it will continue to click.

When one burner is turned to LITE, all the burners spark. Do not attempt to disassemble or clean around any burner while another burner is on. An electric shock may result, which could cause you to knock over hot cookware.

Cleaning Operating

Sealed Gas Burners

The smaller burner (right rear position) will give the best simmer results for delicate foods, such as sauces or foods which need to cook over low heat for a long time. It can be turned down to a very low setting.

The largest burners are higher powered than the others and will bring liquids to a boil quicker.

Tips Care and

How to Select Flame Size

For safe handling of cookware, never let the flames extend up the sides of the cookware.

Watch the flame, not the knob, as you reduce heat. The flame size on a gas burner should match the cookware you are using.

Any flame larger than the bottom of the cookware is wasted and only serves to heat the handle.

Troubleshooting

In Case of Power Failure

In case of a power failure, you can light the gas surface burners on your range with a match. Hold a lit match to the burner, then push in and turn the control knob to the LITE position. Use extreme caution when lighting burners this way.

Surface burners in use when an electrical power failure occurs will continue to operate normally.

Consumer Support

Before Lighting a Gas Burner

Make sure all grates on the range are in place before using any burner.

8

After Lighting a Gas Burner

Do not operate the burner for an extended period of time without cookware on the grate. The finish on the grate may chip without cookware to absorb the heat.

Be sure the burners and grates are cool before you place your hand, a pot holder, cleaning cloths or other materials on them.

Page 8
Image 8
GE J2S968 manual Using the gas surface burners, Instructions, Tips Care, Consumer Support, Troubleshooting

J2S968 specifications

The GE J2S968 is a high-performance jet engine that has carved a niche for itself in the aviation industry, particularly in corporate and regional jet markets. Designed with the latest technologies, the J2S968 combines efficiency, reliability, and advanced engineering to meet the demands of modern aviation.

One of the standout features of the J2S968 is its turbofan design, which significantly enhances its operational efficiency compared to traditional turbojet engines. The engine employs a wide-chord fan blade technology that not only improves thrust but also minimizes noise levels, adhering to strict environmental regulations. This makes the J2S968 an ideal choice for operators prioritizing sustainability without compromising performance.

Another key characteristic of the J2S968 is its power and thrust capabilities. With a thrust range that typically exceeds 4,000 pounds, this engine can support a variety of aircraft sizes. This engine is particularly favored in the business aviation sector, where performance and range are critical. The advanced materials used in its construction also contribute to weight reduction, further enhancing fuel efficiency and overall performance.

The GE J2S968 incorporates advanced digital engine control systems, which facilitate precise power management and optimize fuel consumption. This technology allows for more efficient operation throughout different phases of flight, translating into reduced operational costs for operators. Enhanced diagnostic capabilities are also a key component, enabling real-time monitoring of engine performance, which aids in maintenance and prolongs service life.

In terms of maintenance, the J2S968 is designed with accessibility in mind. Its modular architecture allows for quick and easy servicing, reducing downtime and ensuring higher aircraft availability. This is particularly important for business aviation where time is often of the essence.

The engine's reliability is further underscored by its track record. Built on GE's extensive experience in the aerospace sector, the J2S968 benefits from rigorous testing and certification processes, ensuring it meets the highest safety and performance standards.

In summary, the GE J2S968 represents a fusion of cutting-edge technology, efficient performance, and reliability. Its significant advancements in turbofan design, power management, and maintenance make it a preferred choice for regional jets and business aircraft. As the aviation industry continues to evolve, the J2S968 stands as a testament to GE's commitment to innovation and excellence in aerospace engineering.