Manuals / GE / Kitchen Appliance / Range

GE JBP56, JBP55 PREPARE THE OPENING cent’d, Step Prepare For Electriul Connection, Wire System

Models: JBP56 JBP55

1 36

Download 36 pages 54.6 Kb

Page 31

PREPARE THE OPENING (cent’d)

PREPARE THE OPENING (cent’d)

Nooring Under the Range

Your range, like many other household items, is heavy and can setie into sofi floor coverings such as cushioned vinyl or carpeting. men moving the range on this type of flooring, use care, and follow these simple and inexpensive instructions.

The range should be installed on a 1/4 inch thick sheet of plywood (or similar material) as follows:

When the floor covering ends at the front of the range, the area that the range will rest on should be built up with plywood to the same level or higher than the floor covering. This will allow the range to be moved for cleaning or servicing.

STEP 2

PREPARE FOR ELECTRIUL CONNECTION

Use only a 3-conductor, or if required a 4- conductor range cord set as noted below. These cord sets are provided with ring type terminals.

The electrical rating of the cord must be 125/250 volts minimum, 40 amperes.

NOTE: Only a 4-conductor cord is to be used when the appliance is installed in a mobile home or where local codes do not permit grounding through the neutral.

STEP 3

1.bcate connector block at the bottom rear of range and remove rear wiring cover.

2.Directly below the connector block is a hole with a knockout ring for accommodating conduit fittings. Brackets provided are used to support the flexible cord strain relief, which must be securely attached to the cord set.

CTOR

I

STEP 4

3-WIRE SYSTEM

Power Cord Installation-Insert screws through power cord terminals so that the screws pass through connector block terminals and engage nuts. Tighten screws securely.

Cable Direct InsMation-Clamp bare wires between the connector block terminals and movable nuts with screws tightened securely.

1. Copper Wiring

Connect the neutral or ~rounded wire of the supply circuit to the neutral terminal of the connector block, located in the center. The power leads must be connected to the outside @rass colored) terminals.

NEUTRAL

TERMINAL

NG STRAP

ING TO RANGE)

W~ING: CONNE~OR BLOCK IS ~PROWD FOR COPPER ~RE CONNE~ION ONLY.

(continued next page)

31

Image 31

GE JBP56, JBP55 PREPARE THE OPENING cent’d, Step Prepare For Electriul Connection, Wire System, Nooring Under the Range

Contents

I Useandtire&ln*llation Guide Self-Cleaning Electric RangeConsumer Services Care and CleaningWrite down the model and serial numbers ~ YOU NEED SERVICESave time and money Before you request service ~LP US ~LP YOUAWAmING Self-Cleaning Oven WORTANT SAFETY mSTRUCTIONSOven Do not use aluminum foil to line drip pans Do not self-clean the surface units in the ovenSAVE THESE ~STRUCTIONS ‘Surface Cooking Units~GY’ FEATURES OF YOUR RANGEJBP55 JBP56 JBP58 Qjt’Explained l“ ~ How to Set the ControlsHOW DOES THIS COOKTOP COMPARE TO YOUR OLD ONE? SU~ACE COOmGCookware Cooking Guide Using Heat SettingsSU~ACE COOKWAm TIPS Light over the Surface Units on some modelsWok Cooking SU~ACE COOKWA~ TIPSHOME CANNING TIPS Deep Fat FryingTI ME CLEAN COOKAUTO PBROIL To Cancel the Timer TimerTo Set the Timer To Reset the TimerTo remove the Before Using Your OvenOven Shelves Shelf PositionsOven Shelves How to Set Your Range for BakingBAmNG PreheatingCookies Pan PlacementBaking Pans Baking GuidesTIMED BA~NG How to Time BakeHow to Set Immediate Start and Automatic Stop BA~NGQuick Reminder ADJUST THE OVEN THE~OSTAT-DO ZT YOURSELFYHow to Set Delay Start and Automatic Stop To Adjust the ThermostatUse of Aluminum Foil ROAST~GQ. Why is my roast crumbling when I try to carve it? Questions and AnswersROASTING GU~E Frozen RoastsUse of Aluminum Foil Questions and AnswersQ. Why are my meats not turning out as brown as they should? Q. When broiling, is it necessary to always use a grid in the pan?The oven door should be open to the broil stop position Before a Clean Cycle OPEWT~G T~ SELF-CLEAN~G OVENQuick Reminder CLEAN How to Set the Oven for CleaningTo Stop a Clean Cycle After a Clean Cyclewill damage the door lock Ill\* mechanism OPEWT~G THE SELF-CLEANING OVENHow to Set Delay Start of Cleaning Quick ReminderQ. Should there be an odor during the cleaning? CAm AND CQuestions and Answers Q. What should I do if excessive smoking occurs during cleaning?Clean the area under the drip pans often CAm Am CLEANINGLift-Up Cooktop on some models Surface Units and Drip PansGlass Window Control Panel and KnobsCooktop Surface Light on some models Metal PartsTO CLEAN THE DOOR Inside of the door CAm AND CLEAN~GOven Light Replacement Lift-Off Oven DoorDo not clean the bake element or the broil element Oven Heating ElementiBroiler Pan and Grid Porcelain Enamel CooktopTOOLS YOU WILL NEED ~STALLATION mSTRUCTIONSBEFORE YOU BEGIN N~ ~s appkce must be proper~STEP STEP 3-WIRE SYSTEMPREPARE THE OPENING cent’d STEP PREPARE FOR ELECTRIUL CONNECTIONSTEP ANTI-TIP BRACKET INSTALMTION STEP 4-WIRE SYSTEM SPECIAL GROUNDING INSTRUCTIONS~STALLATION ~STRUCTIONS 2. Muminum WitingPOSSIBLE CAUSE Fluorescent light is loose or defective. Adjust or replacePROBLEM “F- AND A NUMBER” FLASH IN THE DISPLAY OVEN WILLOVEN WILL NOT THE PROBLEM SOLVERPROBLEM 800.626.2000 consumer information serviceGEAnswer Cente~ Parts andAccessoriesWe’ll Be There In-Home Repair SewiceWARRANTY under warrantyWHAT IS COVERED YOUR GENERAL ELECTRIC RANGE