Anti-Tip Bracket Installation, Leveling the Range | GE JBP63, JBP77

Customer Service Troubleshooting Tips Installation Instructions Operating Instructions Safety Information

Installation of the range.

Read these instructions completely and carefully.

8 Anti-Tip Bracket Installation

An Anti-Tip bracket is supplied with instructions for installation in a variety of locations. The instructions include a template, a parts list and a list of tools necessary to complete the installation. Read the Important Safety Information and the instructions that fit your situation before beginning installation.

WARNING

■Range must be secured by Anti-Tip bracket supplied.

■See instructions to install (supplied with bracket).

■Unless properly installed, the range could be tipped by stepping or sitting on the door. Injury might result from spilled hot liquids or from the range itself.

Bracket

Wall plate

Screw must enter wood or metal

Typical installation of anti-tip bracket attachment to wall.

9 Leveling the Range

The range must be level. Leveling feet are located at each corner of the base of the range. Remove the storage drawer or kick panel (depending on your model) and using channel locks, rotate the leveling feet in and out as required to level the range. (For instructions on how to remove and replace the storage drawer or the kick panel, see the Care and cleaning of the range section.)

On some models, there are plastic covers which may be removed for easy adjustment (just squeeze and pull).

One of the rear leveling feet will engage the Anti-Tip bracket (allow for some side to side adjustment). Allow a minimum clearance of 1/8″ between the range and the leveling foot that is to be installed into the Anti-Tip bracket.

Check the range for proper installation into the Anti-Tip bracket by removing the kick panel or storage drawer and inspecting the rear leveling leg. Make sure it fits securely into the slot.

10 Final Check

Be sure all range controls are in the OFF position before leaving the range.

40

Image 40

GE JBP63, JBP77, JBP76, JBP75 owner manual Anti-Tip Bracket Installation, Leveling the Range, Final Check

Contents

GE Appliances GE Answer Center Staple sales slip or cancelled check here Congratulations You Are Now Part of the GE FamilyWrite the model and serial numbers here You can find them on a label behind GE & You Service Partnership Fiberglass insulation in self-clean ovens gives off a very Small amount of carbon monoxide during the cleaning cycleAll ranges can tip and injury could result California Safe Drinking Water and Toxic Enforcement Safety Precautions Safety Information When Cooking PORK… Oven SELF-CLEANING Oven Radiant Surface Units Page Instructions Safety Information REMEMBER… Using the surface units How to SetIndicator Lights About the radiant surface units… Selecting types of cookware Using the oven controls Instructions Oven Control Settings Oven on Light Using the oven Before you begin… Preheating and Pan Placement How to Set the Oven for BroilingTroubleshooting Tips Customer Service Aluminum Foil Broiling guide Comments Using the clock and timer Automatic Stop Make sure the oven clock shows the correct time of dayPress Cook Time ON/OFF Press Start Time ON/OFF For Models with Pads and an Oven Temperature Knob For Models with Only an Oven Temperature KnobLatch Door Indicates the thermostat will be set 20F. cooler Using the self-cleaning oven Before a Clean CycleCustomer Service Troubleshooting How to Set the Oven for Cleaning How to Delay the Start of Cleaning After a Clean CycleTroubleshooting Tips Customer Service Press the Start Time ON/OFF pad Care and cleaning of the range Control Panel and KnobsOven Vent Painted Surfaces To clean the inside of the door To clean the outside of the doorLift-Off Oven Door Do not lift the door by the handle Oven Light Replacement on some models Oven Heating ElementsOven Shelves To remove the cover To remove the storage drawer Broiler Pan & GridTo replace the storage drawer Cleaning the glass cooktop Daily CleaningFor heavy, burned-on soil National Parts Center Special Care Installation of the range Wiring must conform to National Electric Codes Prepare the Opening Flooring Under the Range Prepare for Electrical Connection Power Cord Strain Relief Installation Strain relief, they can be removed for better fit Wire Power Cord Installation Do not remove ground strap connection Before After Wire Conduit Installation Connector block terminal Bare wire Leveling the Range Anti-Tip Bracket InstallationFinal Check Before you call for service… Blank or indicator When range isFrequent cycling Off and on Food does not bake Or roast properlyFood does not Broil properly At Broil Oven temperature Clock and timerSelf-clean Self-clean cycle Oven not clean After a clean cycleExcessive smoking Oven door will Is on when you Power outageWant to cook A number GE Electric Range Warranty Five Years Replacement glass cooktop if it should crack dueWe Will Replace, At No Charge To You What GE Will Not Cover In-Home Repair Service 800-GE-CARES Service Telephone NumbersTDD 800-TDD-GEAC