Routine Monthly Maintenance, Test, Adjustment

WARNING

• Garage door hardware (springs, cables, brackets,

pulleys, etc.) are under extreme pressure and

tension.

• DO NOT attempt to repair or adjust door

springs or any hardware, and DO NOT OPERATE

garage door automatically or manually if door

is improperly balanced or springs are broken.

WARNING

Use wall console supplied with opener. Other approved wall consoles may be available. Unapproved or incompatible wall consoles can cause the opener to operate unexpectedly.

Safe-T-Beam® (STB) SYSTEM CHECK

• STB Red and Green LEDs ON steady, system OK

– CONTACT A TRAINED DOOR SYSTEM

TECHNICIAN.

ROUTINE MONTHLY MAINTENANCE

Basic monthly maintenance tasks.

•Safe-T-Beam® System Check

•Door balance

•Contact reverse

Instructions for these tasks and others are found on

•STB Red LED flashes

–Check for obstruction

–Check alignment

–Verify wire routing from STBs to STB connection in powerhead

–Check for signal interference from another Safe-T-Beam® unit

FROM STBs

STB

FROM WALL

CONSOLE

NOT NOT

USED USED

BWC IWC

the following pages.

DOOR BALANCE (SPRING TENSION)

•No STB Red or Green LED displayed

–Check wiring and wire connections

•With the door closed, pull release handle DOWN and let go to release door carriage assembly from drive system.

•Raise door manually approximately 3’- 4’ and release.

–Door should remain stationary or move very slightly.

–If door moves quickly, CONTACT A TRAINED DOOR SYSTEM TECHNICIAN.

•Close the door.

•Verify shuttle arm is in the up position.

(refer to page 19)

–Operate door using remote or wall console.

–Door will re-attach itself to carriage assembly.

3’ - 4’

Sectional Door

FIG. 6-1 Door balance

3’ - 4’

One-Piece Door

CONTACT REVERSE TEST (Monthly test)

The Force and Limit settings MUST be COMPLETED before testing. (See pages 6-7)

1.Test.

•Open garage door using wall console.

–Place a 2" x 4" board (laid flat) under center of garage door opening (Fig. 6-2).

•Close garage door using wall console.

•When door contacts board, the door must stop (within 2 seconds) and reverse direction returning to open position.

2.Adjustment.

•If the door:

–Stops before it contacts the 2 x 4 board, it may simply be responding to an improperly set down limit. Return to pages 6-7 and repeat steps 1 through 10 to correct down limit.

–Stops after contacting the 2 x 4 board and does not reverse, it may need an adjustment to the down limit. Return to pages 6-7 and repeat steps 1 through 10 to correct down limit.

•Test again. Repeat as necessary until door reverses upon contacting board.

FIG. 6-2 2 x 4 under center of door opening

12/2010

3064H, 3064 specifications

The Genie 3064 and 3064H are renowned models in the realm of compact aerial work platforms. These versatile machines are designed for indoor and outdoor construction, maintenance, and industrial applications. Their compact design and advanced technologies make them suitable for tight spaces, while their impressive lift capabilities ensure productivity and safety.

One of the defining features of the Genie 3064 series is its impressive working height. The 3064 model can reach heights of up to 36 feet, enabling operators to perform tasks high above the ground safely and efficiently. The 3064H variant, with its hybrid technology, allows for seamless transitions between electric and diesel power, making it exceptionally versatile for various job sites. The hybrid engine ensures minimal emissions, which is particularly beneficial for indoor applications where air quality is a concern.

The Genie 3064 series boasts a maximum capacity of 500 pounds. This makes it ideal for tasks that require multiple workers, tools, and equipment. The platform's extension offers increased reach, allowing users to work on a wider area without the need to reposition the lift frequently. This feature enhances productivity and minimizes downtime, crucial factors in any construction or maintenance project.

Both models come equipped with Genie’s signature technology, the Smart Link Control System, which provides intuitive operation and helps reduce training time for new operators. The user-friendly interface integrates critical information, including platform height, load capacity, and battery levels, ensuring that operators have all necessary data at their fingertips.

The machines are built with durability in mind. High-grade steel and robust components ensure they can withstand the rigors of challenging job sites. The steel chassis provides stability while the non-marking tires protect floors in sensitive indoor environments.

Safety is a top priority with the Genie 3064/3064H series. Features like guardrails, emergency stop buttons, and a tilt sensor are standard, ensuring compliance with stringent safety regulations. The design allows for rapid deployment, reducing setup time and enhancing accessibility.

In summary, the Genie 3064 and 3064H aerial work platforms combine innovative technology, robust construction, and user-friendly features. Their versatility, safety measures, and exceptional performance make them a preferred choice for contractors, maintenance teams, and anyone needing reliable access solutions in various environments.

Genie 3064 Routine Monthly Maintenance, Safe-T-Beam System Check Door balance Contact reverse

Models: 3064H 3064