2060-3060 eng.qxd 11/9/05 11:02 AM Page 11

ACCESSORIES

Programming 1: PROGRAMMING THE

REMOTE CONTROLS

NOTE

Each Remote Control must be programmed separately.

The Remote Controls will not cause the door Opener to close the garage door if the Safe-T- Beam® System is malfunctioning.

When programming the Remote Controls, they must be at least 24" from the Antenna Wire.

If the red Learn Indicator Light blinks approximately 4 times per second, programming has stopped. If programming has stopped, repeat the above steps.

Each Button on a 2 or 3 Button Remote Control is for a different Opener. You cannot use more than one Button per Remote, per Opener.

A maximum of seven Remote Controls or Wireless Keypads can be stored into the Receiver at one time. If a Remote Control becomes lost, or if you want to delete a Remote Control or Wireless Keypad, see “To Erase All Receiver Memory.”

ATo program one Button of a Remote Control (Figure 12):

Locate Learn Button and Learn Indicator Light near Terminal Strip on Power Head (Figure 13).

Press and release Learn Button. Red Learn Indicator Light will blink 2 times per second.

Press Remote Control Button once within 30 seconds. Red Learn Indicator Light will stay lit.

Press Remote Control Button again. Red Learn Indicator Light will go out, indicating that memory is stored.

BProgram each additional Remote using step A above (up to seven).

To Erase All Remotes from Power Head Memory

APress and hold Learn Button on Power Head for 10 seconds or until Learn Indicator Light goes out. Memory is erased:

Program Transmitter/Receiver again as needed.

To Replace Remote Control Battery

AFOR NON-FLASHLIGHT MODELS

Pop off the back of the transmitter.

Use coin, pen, screwdriver or any similar device.

Replace old Battery with new coin type battery.

Replace back of remote.

BFOR FLASHLIGHT MODELS

Slide open battery cover.

Replace old Battery with new AAA battery.

Replace battery cover.

WARNING

A moving garage door may cause serious injury or death.

Keep people clear of opening while door is moving.

Do not allow children to play with the Remote Controls. If the Safety Reverse does not work properly:

Close the door and disconnect the Opener using the Emergency Release Cord.

Do not use the door Opener, Remote Controls, or Wireless Keypad.

Refer to the door and door Opener Owner’s Manuals before attempting any repairs.

Remote Control Operation

APress Button on Remote Control. Garage door will move.

BPress Button again. Garage door will stop:

The door automatically stops at the end of the open or close cycle.

CPress Button again. Garage door will reverse.

315 Mhz

 

315 Mhz

Frequency

Frequency

Switch

Switch

390 Mhz

 

390 Mhz

1 Button Compact Remote

3 Button Compact Remote

w/Docking Station

w/Docking Station

Figure 12 Genie Remote Controls

 

 

 

1

2

3

4

Figure 13 Learn Code Button and Indicator Light

 

DSome Remote Controls are equipped with a flashlight. The logo is the button which operates the light. There is a backlight under the button. When it does not light, it indicates the battery needs replaced.

 

 

 

 

 

 

 

Frequency

Flashlight Button

 

 

 

 

 

 

Switch

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1 Button Remote

3 Button Remote

3 Button Large

w/Flashlight

w/Flashlight

Remote

w/Flashlight

Figure 14 Genie Remote Controls

For Help, call 1-800-35-GENIE or visit www.geniecompany.com

11

Page 11
Image 11
Genie directlift 2060 warranty Accessories, Programming 1 Programming, Remote Controls, Pop off the back of the transmitter