Console Redirection, FlowControl | Gigabyte GS-R12T4H2-RH specification

Use Serial Port A as the COM port address. Use Serial Port B as the COM port address. Disable this function. (Default setting)

GS-R12T4H2-RH Rack Mount Server

Console Redirection

Figure 5-2: Console Redirection

Console Redirection

If this option is set to enabled, it will use a port on the motherboard to run console redirection function.

On-board COM A

On-board COM B Disabled

FlowControl

This option provide user to enable the flow control function.

None	Not supported.
XON/XOFF	Software control.
CTS/RTS	Hardware control. (Default setting)

Baud Rate

7 7

Image 77

Gigabyte GS-R12T4H2-RH manual Console Redirection, FlowControl, Baud Rate

Contents

Service Guide Preface Table of Contents Power Security Server  Precaution for Product with Laser Devices  Important safety information  FCC part 68 applicable to products fitted with USA modems  Federal Communications Commission FCC Statement  Canadian Department of Communications Compliance Statement Class a equipment System Specification Super I/O System Hardware Installation Remove the chassis cover Installing the Processor Installing the Heat Sink Installing the Memeory Module Code 7 61716 1 5 Channel a Channel B Channel C Dimm Population Table Quad-Rank Single-Rank Dual-Rank Installing the PCI Expansion Card GS-R12T4H2-RH Rack Mount Server Installing the Hard Disk Drive HDD Security Lock Installing and Replacing the FAN Duct Replacing the FAN Assemblly Replacing the Motherboard Replacing the Power Supply GS-R12T4H2-RH Rack Mount Server Replacing the Chassis Cover Front View of GS-R12T4H2-RH Appearance of GS-R12T4H2-RH Rear View of GS-R12T4H2-RH Indicator Color State Description Front Panel LED Indicator LAN1   LAN port LED Indicator Hard Disk Drive LED Description Description SAS/SATA HDD indicator Green Red Code Description GC-BS14U-RH Back plane board Components Intel ICH10R System Block Diagram Suggest Icon Description Connector Icon Description GA-7TTSE-RH Motherboard Component Motherboard Placement and Jumper Setting Item Component CLRCMOS1 Clear Cmos jumper Jumper SettingBIOSRVCR1 Bios Revocery jumper PASSDIS1 Skip Supervisor password jumper Meenable BMC Selection jumperJPSTRAP2/ JPSTRAP8 PilotII firmware upgrade jumper CLRRTC1 Clear RTC jumper Expansion Card Components Description Bios Setup  Power Status Page Setup Menu / Option Page Setup Menu Boot MainMenu System Date BIOSInformantionSystem Time Processor Information TotalMemory Advanced Processor Configuration Multiprocessor Specification Processor ConfigurationExecute Disable Bit Intel R Virtualization Technology Fast String Operations Machine CheckingSetMaxExtCPUID=3 EchoTPR EISTPSDFunction Processor Power ManagementEist GV3 & C State State TurboModeCPU C State Osacpi C3 Report Acpi Mwait extensions CPU C7 ReportPackage C State Limit Memory Configuration Memory RAS Mode Memory Control SettingsChange Interleave setting Rank Interleave setting Advanced Chipset Configuration 1 Intel VT for Directed I/O VT-d InterruptRemapping Intel VT forDirected I/O VT-dCoherency Support PassThrough DMA QPI Link Fast Mode QPI Control SettingsQPI Error Report MemoryECCErrorLog Onboard LAN iSCSI Boot ROM PCI ConfigurationOnboard LAN1 Control LAN1OptionROM Legacy USB Support LAN2OptionROM Sata Configuration Sata Configuration Sata Port 0/1/2/3/4/5 Serial ATA Multi-Sector Transfer Serial Port B DeviceConfigurationSerial Port a GS-R12T4H2-RH Rack Mount Server Post Error Pause Boot DeviceConfigurationBoot -time Diagnostic Screen NumLock Thermal and Acoustic Configuration Close loop Thermal Throttle Temperature hysteresisTemperature guardband After Power Failure Power Security Set Supervisor Password Password on boot Set User Password Server System Management BMC IPAddress Source System Management Console Redirection Console RedirectionFlowControl Baud Rate Continue C.R. after Post Terminal Type Boot Exit Discarding Changes Exit Saving Changes Save Changes Load SettupDefaultDiscard Changes