Terminal Type, Continue C.R. after Post | Gigabyte GS-R12T4H2-RH

BIOS Setup

This option allows user to set the specified baud rate.

Options

300, 1200, 2400, 9600, 19.2K, 38.4K, 57.6K, 115.2K.

Terminal Type

This option allows user to select the specified terminal type. This is defined by IEEE.

OptionsVT100, VT100 8bit, PC-ANSI 7bit, PC-ANSI, VT100+, VT-UTF8,

ASCII.

Continue C.R. after POST

This option allows user to enable console redirection after O.S has loaded.

On	Enable console redirection after O.S has loaded.
Off	Disable this function. (Default setting)

7 8

Image 78

Gigabyte GS-R12T4H2-RH manual Terminal Type, Continue C.R. after Post

Contents

Service Guide Preface Table of Contents Power Security Server  Important safety information  Precaution for Product with Laser Devices  Federal Communications Commission FCC Statement  FCC part 68 applicable to products fitted with USA modems  Canadian Department of Communications Compliance Statement Class a equipment System Specification Super I/O System Hardware Installation Remove the chassis cover Installing the Processor Installing the Heat Sink Installing the Memeory Module 7 6 1716 1 5Code Dimm Population Table Channel a Channel B Channel C Quad-Rank Single-Rank Dual-Rank Installing the PCI Expansion Card GS-R12T4H2-RH Rack Mount Server Installing the Hard Disk Drive HDD Security Lock Installing and Replacing the FAN Duct Replacing the FAN Assemblly Replacing the Motherboard Replacing the Power Supply GS-R12T4H2-RH Rack Mount Server Replacing the Chassis Cover Appearance of GS-R12T4H2-RH Front View of GS-R12T4H2-RH Rear View of GS-R12T4H2-RH Front Panel LED Indicator Indicator Color State Description LAN1 LAN port LED Indicator   Description SAS/SATA HDD indicator Green Red Hard Disk Drive LED Description GC-BS14U-RH Back plane board Components Code Description System Block Diagram Intel ICH10R Connector Icon Description Suggest Icon Description Motherboard Placement and Jumper Setting GA-7TTSE-RH Motherboard Component Item Component Jumper Setting BIOSRVCR1 Bios Revocery jumperCLRCMOS1 Clear Cmos jumper JPSTRAP2/ JPSTRAP8 PilotII firmware upgrade jumper Meenable BMC Selection jumperPASSDIS1 Skip Supervisor password jumper CLRRTC1 Clear RTC jumper Expansion Card Components Description Bios Setup  Boot Status Page Setup Menu / Option Page Setup Menu Power MainMenu System Time BIOSInformantionSystem Date Processor Information TotalMemory Advanced Processor Configuration Execute Disable Bit Processor ConfigurationMultiprocessor Specification Intel R Virtualization Technology SetMaxExtCPUID=3 Machine CheckingFast String Operations EchoTPR Processor Power Management Eist GV3 & C StateEISTPSDFunction CPU C State TurboModeState Osacpi C3 Report CPU C7 Report Package C State LimitAcpi Mwait extensions Memory Configuration Change Interleave setting Memory Control SettingsMemory RAS Mode Rank Interleave setting Advanced Chipset Configuration 1 Intel VT for Directed I/O VT-d Coherency Support Intel VT forDirected I/O VT-dInterruptRemapping PassThrough DMA QPI Error Report QPI Control SettingsQPI Link Fast Mode MemoryECCErrorLog Onboard LAN1 Control PCI ConfigurationOnboard LAN iSCSI Boot ROM LAN1OptionROM LAN2OptionROM Legacy USB Support Sata Configuration Sata Configuration Serial ATA Sata Port 0/1/2/3/4/5 Multi-Sector Transfer DeviceConfiguration Serial Port aSerial Port B GS-R12T4H2-RH Rack Mount Server Boot DeviceConfiguration Boot -time Diagnostic ScreenPost Error Pause NumLock Thermal and Acoustic Configuration Temperature hysteresis Temperature guardbandClose loop Thermal Throttle Power After Power Failure Set Supervisor Password Security Set User Password Password on boot Server System Management System Management BMC IPAddress Source FlowControl Console RedirectionConsole Redirection Baud Rate Terminal Type Continue C.R. after Post Boot Exit Saving Changes Exit Discarding Changes Load SettupDefault Discard ChangesSave Changes