Installing and Replacing the FAN Duct | Gigabyte GS-R12T4H2-RH

GS-R12T4H2-RH Rack Mount Server

Installing and Replacing the FAN Duct

Step 1 Remove the airducts from the chassis by pulling the rear edge in the direction of the arrow Step 2 With fan duct installation, align the fan duct with the guiding groove. Push down the fan duct

into chassis until its firmly seats.

1

2

2 3

Image 23

Gigabyte GS-R12T4H2-RH manual Installing and Replacing the FAN Duct

Contents

Service Guide Preface Table of Contents Power Security Server  Precaution for Product with Laser Devices  Important safety information  FCC part 68 applicable to products fitted with USA modems  Federal Communications Commission FCC Statement  Canadian Department of Communications Compliance Statement Class a equipment System Specification Super I/O System Hardware Installation Remove the chassis cover Installing the Processor Installing the Heat Sink Installing the Memeory Module Code 7 61716 1 5 Channel a Channel B Channel C Dimm Population Table Quad-Rank Single-Rank Dual-Rank Installing the PCI Expansion Card GS-R12T4H2-RH Rack Mount Server Installing the Hard Disk Drive HDD Security Lock Installing and Replacing the FAN Duct Replacing the FAN Assemblly Replacing the Motherboard Replacing the Power Supply GS-R12T4H2-RH Rack Mount Server Replacing the Chassis Cover Front View of GS-R12T4H2-RH Appearance of GS-R12T4H2-RH Rear View of GS-R12T4H2-RH Indicator Color State Description Front Panel LED Indicator LAN1   LAN port LED Indicator Hard Disk Drive LED Description Description SAS/SATA HDD indicator Green Red Code Description GC-BS14U-RH Back plane board Components Intel ICH10R System Block Diagram Suggest Icon Description Connector Icon Description GA-7TTSE-RH Motherboard Component Motherboard Placement and Jumper Setting Item Component CLRCMOS1 Clear Cmos jumper Jumper SettingBIOSRVCR1 Bios Revocery jumper CLRRTC1 Clear RTC jumper Meenable BMC Selection jumperPASSDIS1 Skip Supervisor password jumper JPSTRAP2/ JPSTRAP8 PilotII firmware upgrade jumper Expansion Card Components Description Bios Setup MainMenu Status Page Setup Menu / Option Page Setup Menu Power  Boot Processor Information BIOSInformantionSystem Date System Time TotalMemory Advanced Processor Configuration Intel R Virtualization Technology Processor ConfigurationMultiprocessor Specification Execute Disable Bit EchoTPR Machine CheckingFast String Operations SetMaxExtCPUID=3 EISTPSDFunction Processor Power ManagementEist GV3 & C State Osacpi C3 Report TurboModeState CPU C State Acpi Mwait extensions CPU C7 ReportPackage C State Limit Memory Configuration Rank Interleave setting Memory Control SettingsMemory RAS Mode Change Interleave setting Advanced Chipset Configuration 1 Intel VT for Directed I/O VT-d PassThrough DMA Intel VT forDirected I/O VT-dInterruptRemapping Coherency Support MemoryECCErrorLog QPI Control SettingsQPI Link Fast Mode QPI Error Report LAN1OptionROM PCI ConfigurationOnboard LAN iSCSI Boot ROM Onboard LAN1 Control Legacy USB Support LAN2OptionROM Sata Configuration Sata Configuration Sata Port 0/1/2/3/4/5 Serial ATA Multi-Sector Transfer Serial Port B DeviceConfigurationSerial Port a GS-R12T4H2-RH Rack Mount Server Post Error Pause Boot DeviceConfigurationBoot -time Diagnostic Screen NumLock Thermal and Acoustic Configuration Close loop Thermal Throttle Temperature hysteresisTemperature guardband After Power Failure Power Security Set Supervisor Password Password on boot Set User Password Server System Management BMC IPAddress Source System Management Baud Rate Console RedirectionConsole Redirection FlowControl Continue C.R. after Post Terminal Type Boot Exit Discarding Changes Exit Saving Changes Save Changes Load SettupDefaultDiscard Changes