Graco 244561 Replacing Display Board

Service

309301G 39

Replacing Display Board

2. Remove controller cover (A). See page 37, steps 1-4.

3. Unplug keypad (D) ribbon cable from the display board. Note position of cable in connec-

tor. Arrow indicates pin #1, reconnect with pin #1 engaged.

4. Remove four nuts (C1) from the board. See FIG. 15.

5. Disconnect ground wire.

6. Unplug three fiber optic connectors (C3) from the diodes, then remove display board (F).

7. Install parts in reverse order of disassembly.

1. Turn off controller power switch.

•If replacing software chip, use a chip puller to remove it.

•Spacers (G) must be used in correct positions to protect the display and board.

FIG. 15

TI1056A

Contents

Main Instructions-Parts ProDispense Part No. 244561 Electronic Preset Dispense System 309301G Contents Page ProDispense System Components Conventions Warning Symbols Caution Symbol Note Symbol WARNING FIRE, EXPLOSION, AND ELECTRIC SHOCK HAZARD TOXIC FLUID HAZARD EQUIPMENT MISUSE HAZARD WARNING HIGH PRESSURE FLUID HAZARD/SKIN INJECTION HAZARD LOW PRESSURE FLUID HAZARD Overview How the ProDispense System Works Usage Fluid Supply Choice of Recipe Dispense or Fluid Dispense Main Components ProDispense Controller Display and EasyKey Pad Page Power Switch (A) Operation Mode Switch (B) and Key (C) Dispense Mode Setup Mode Remote Operator Stations C Fluid Panels Page Installation Install the Fluid Supplies Mount the Fluid Panel(s) Connect the Air and Fluid Lines Fluid Panel 244599 and 244600 Fluid Panel 244601 and 246837 Fluid Panel 246838 Install the Remote Operator Station Mount the Controller Connect the Cables and Power Cord Ground the System ProDispense Controller: Fluid Panels: Check the Resistance Connect a Printer (optional) Connect to a PC or Alarm (optional) Page Startup Pressure Relief Procedure Shutdown Setup Mode Screen Navigation To enter Setup Mode: To exit Setup Mode: System Setup Screen To setup the system: Fluid Setup Screen To set up the fluids: Recipe Setup Screen To setup the recipes: To calibrate a meter: Dispense Mode Screen Navigation Run Screen Idle, Dispense, and Alarm Status Idle Dispense Alarm Recipe Dispense Fluid Dispense Fluid Totals Screen ! Alarm History Screen Out of Tolerance Alarm Dispense Timeout Alarm Invalid K-factor Alarm Memory Failure Alarm Operation Procedures Loading Fluid Lines Manual Dispense Automatic Dispense Purging Fluid Emergency Stop Troubleshooting Problem Cause Solution Service Removing and Installing Controller Page Replacing Display Board Replacing Display Replacing Membrane Replacing Main Board Replacing Power Supply Replacing Fluid Panel Junction Box Page Page Servicing Fluid Panel 244599 Replacing Fluid Meter or Solenoid Page Servicing Fluid Panel 244600 Replacing Fluid Meter or Solenoid Page Servicing Fluid Panel 244601 and 246837 Replacing Fluid Meter, Solenoid, or Dispense Valve Page Servicing Fluid Panel 246838 Replacing Solenoid or Dispense Valve Page Servicing Fluid Panel 246839 Replacing Fluid Meter, Solenoid, or Dispense Valve Page Wiring Charts Control Box Wiring Chart Page Page Accessories Wiring Chart Field Wiring Chart - Output Page Parts Part No. 244561, Controller Item 18 Cover Assembly Part No. 245222 Part No. 244599, Fluid Panel Part No. 244600, Fluid Panel Part No. 244601, Fluid Panel Part No. 246837, Fluid Panel Part No. 246838, Fluid Panel Part No. 246839, Fluid Panel Page Technical Data Power Requirements No. of Recipes. . . . . . . . . . . . . . . . . . . . 250 maximum Cable Lengths Fluid Panels 244599 Oil /Lubricant 244600 Water/Antifreeze 246837 Grease/Paint 246838 Meter-less (flow meter supplied by user) 246839 Grease/Paint/Sealants Accessories and Kits Wetted Parts Part Number Description Graco Standard Warranty Graco Information