Manuals / Graco Inc / Power Tools / Paint Sprayer

Graco Inc 309856P, TI3840a, 2004230905 important safety instructions Adjust Rear Rod Seal

Models: TI3840a 309856P 309856 2004230905

1 56

Download 56 pages 7.94 Kb

Page 29

Adjust Rear Rod Seal

1. Follow Pressure Relief Procedure, page 18.

2. Flush Gun, page 22.

3. Remove fluid manifold (G). Leave air connected.

G

TI3852a

4. Disassemble Front End, page 35.

5. Assemble fluid housing (7) backwards onto lubri-

cated purge rod (31). Adjust rear rod seal nut (23) with nut driver until drag is felt when sliding on rod.

7 31

23

TI3831a

6.

7.

8.

9.

Maintenance

Remove fluid housing (7) from rod (31).

Reassemble Front End, page 36.

Adjust Purge Rod, page 15.

Attach fluid manifold. Return gun to service.

309856P

29

Image 29

Graco Inc 309856P, TI3840a, 2004230905 important safety instructions Adjust Rear Rod Seal

Contents

Plural Component, Impingement Mix Mechanical Purge Spray Gun Contents Manual Conventions Pressure in psi MPa, bar List of Models/Selection GuideStandard Round Pattern Guns Standard Flat Pattern Guns Flow Rate in gpm lpm Direct Impingement Round Pattern GunsDirect Impingement Flat Pattern Guns Four-Hose Gun Personal Protective Equipment Fire and Explosion Hazard Key Overall ViewIsocyanate Hazard Piston Safety LockKeep a and B Components Separate GroundingISO SetupDisengage piston safety lock, 1/4 Turn Adjust Purge RodAdjust Flat CeramTip Shutdown Follow Pressure Relief Procedure,Daily Shutdown Shutdown for More than a DayPressure Relief Procedure Optional Fluid Manifold Position Optional ConfigurationsOptional Hose Position Follow Pressure Relief Procedure, page 18. AlsoFluid Hoses Air HoseMaintenance Clean Air Cap Clean Outside of GunClean Muffler Clean Fluid ManifoldCleaning Component a ISO Ports Clean Slip-Fit Polycarballoy Mix ModuleImpingement Port Drill Counterbore Drill Impingement Port Cleanout Drill SizesXF1313 #81 External Quick Cleaning Method Clean CeramTipCleanout Drill Sizes for Round CeramTips Round CeramTipStuck Purge Rod Clean Purge RodAdjust Purge Rod, Disassemble Front End, Adjust Front Rod SealReassemble Front End, Adjust Purge Rod, Adjust Rear Rod Seal See Clean Purge Rod, TroubleshootingAdjust Rear Rod Seal, Gun Detriggered Mechanical Purging Theory of OperationGun Triggered Fluid Spraying Cutaway View Tools Required RepairLubrication Replace CeramTipDisassemble Front End Reassemble Front End Adjust Purge Rod, Slip-Fit Polycarballoy Mix Module Attach fluid manifold. Return gun to service Rear Rod Seal Check Valves Piston and Purge Rod Install piston safety lock assembly until bottomed out Air Valve Piston Safety Lock309856P Flush Manifold Detail PartsHandle Part No. Description QtySlip-Fit Polycarballoy Mix Module Part Numbering Code Slip-Fit Polycarballoy Mix Module KitsStandard Round Pattern Guns Standard Flat Pattern GunsDirect Impingement Flat Pattern Guns Direct Impingement Round Pattern GunsRound CeramTip Part Numbering Code CeramTip KitsFlat CeramTip Part Numbering Code Flat CeramTipsKit Part No Qty in Kit Drill Bit Size Illustration Nominal Drill Bit KitsCheck Valve Filter Screen Kits 10 per kit Gun Repair KitsAccessories Pour Nozzle Kit Solvent Flush Pail KitHose Adapter Kits Category Data Technical DataToll Free Graco Standard WarrantyGraco Information