Technical Data, Category Data | Graco Inc 2004230905, 309856P

Technical Data

Technical Data

Category	Data
Maximum Fluid Working Pressure	3500 psi (24.2 MPa, 242 bar)
Minimum Air Inlet Pressure	80 psi (0.55 MPa, 5.5 bar)
Maximum Air Inlet Pressure	130 psi (0.9 MPa, 9 bar)
Maximum Fluid Temperature	200° F (94° C)
Air Inlet Size	1/4 npt Quick Disconnect Nipple
A Component (ISO) Inlet Size	-5 JIC; 1/2-20 UNF
B Component (Resin) Inlet Size	-6 JIC; 9/16-18 UNF
Typical Flow Rate	See charts pages 4-7.
Sound Pressure	70 dB(A), at 100 psi (0.7 MPa, 7 bar)
Sound Power, measured per ISO	79.9 dB(A), at 100 psi (0.7 MPa, 7 bar)
9416-2
Length	7.6 in. (193 mm)
Height	8.1 in. (206 mm)
Width	3.1 in. (79 mm)
Weight	2.9 lb (1.32 kg)
	Aluminum, stainless steel, carbon steel, chemically resistant o-rings,
Wetted Parts	ultra-high molecular weight polyethylene (UHMWPE), Polycarballoy™,
	CeramTip™

All other brand names or marks are used for identification purposes and are trademarks of their respective owners.

309856P

55

Image 55

Graco Inc 2004230905, 309856P, TI3840a important safety instructions Technical Data, Category Data

Contents

Plural Component, Impingement Mix Mechanical Purge Spray Gun Contents Manual Conventions Standard Round Pattern Guns List of Models/Selection GuidePressure in psi MPa, bar Standard Flat Pattern Guns Flow Rate in gpm lpm Direct Impingement Round Pattern Guns Direct Impingement Flat Pattern Guns Four-Hose Gun Personal Protective Equipment Fire and Explosion Hazard Key Overall View Grounding Piston Safety LockIsocyanate Hazard Keep a and B Components Separate ISO Setup Disengage piston safety lock, 1/4 Turn Adjust Purge Rod Adjust Flat CeramTip Shutdown for More than a Day Follow Pressure Relief Procedure,Shutdown Daily Shutdown Pressure Relief Procedure Optional Fluid Manifold Position Optional Configurations Air Hose Follow Pressure Relief Procedure, page 18. AlsoOptional Hose Position Fluid Hoses Maintenance Clean Fluid Manifold Clean Outside of GunClean Air Cap Clean Muffler Cleaning Component a ISO Ports Clean Slip-Fit Polycarballoy Mix Module Impingement Port Drill Counterbore Drill Impingement Port Cleanout Drill Sizes XF1313 #81 Round CeramTip Clean CeramTipExternal Quick Cleaning Method Cleanout Drill Sizes for Round CeramTips Adjust Purge Rod, Clean Purge RodStuck Purge Rod Reassemble Front End, Adjust Purge Rod, Adjust Front Rod SealDisassemble Front End, Adjust Rear Rod Seal See Clean Purge Rod, Troubleshooting Adjust Rear Rod Seal, Gun Triggered Fluid Spraying Theory of OperationGun Detriggered Mechanical Purging Cutaway View Replace CeramTip RepairTools Required Lubrication Disassemble Front End Reassemble Front End Adjust Purge Rod, Slip-Fit Polycarballoy Mix Module Attach fluid manifold. Return gun to service Rear Rod Seal Check Valves Piston and Purge Rod Install piston safety lock assembly until bottomed out Air Valve Piston Safety Lock 309856P Flush Manifold Detail Parts Handle Part No. Description Qty Standard Flat Pattern Guns Slip-Fit Polycarballoy Mix Module KitsSlip-Fit Polycarballoy Mix Module Part Numbering Code Standard Round Pattern Guns Direct Impingement Flat Pattern Guns Direct Impingement Round Pattern Guns Flat CeramTips CeramTip KitsRound CeramTip Part Numbering Code Flat CeramTip Part Numbering Code Kit Part No Qty in Kit Drill Bit Size Illustration Nominal Drill Bit Kits Check Valve Filter Screen Kits 10 per kit Gun Repair Kits Accessories Hose Adapter Kits Solvent Flush Pail KitPour Nozzle Kit Category Data Technical Data Graco Information Graco Standard WarrantyToll Free