Configuration Guide

The GXP1100/1105 can be configured in two ways:

-IVR MENU from the keypad

-Web GUI embedded on the phone

CONFIGURATION VIA IVR MENU

GXP1100/1105 has a built-in voice prompt menu for simple device configuration. Pick up the handset and dial “***” to use the IVR menu.

Table 9: GXP1100/1105 IVR Menu Definitions

 

 

 

 

 

 

 

 

 

 

Menu

 

Voice Prompt

 

 

Options

 

 

 

 

 

 

 

Main Menu

 

“Enter a Menu Option”

 

 

Press “*” for the next menu option.

 

 

 

 

 

 

Press “#” to return to the main menu.

 

 

 

 

 

 

Enter 01 – 05, 07, 10 - 17, 47, 86 or 99 Menu option.

 

 

 

 

 

 

 

01

 

“DHCP Mode”

 

Enter “9” to toggle the selection.

 

 

 

“PPPoE Mode ”

 

 

If users select “Static IP Mode”, users need configure all the

 

 

 

“Static IP Mode”

 

 

IP address information through menu 02 to 05 as below.

 

 

 

 

 

 

If users select “Dynamic IP Mode”, the device will retrieve all

 

 

 

 

 

 

IP address information from DHCP server automatically after

 

 

 

 

 

 

user reboots the device.

 

 

 

 

 

 

 

02

 

“IP Address “ + IP address

 

The current WAN IP address is announced.

 

 

 

 

 

 

Enter 12-digit new IP address if in Static IP Mode.

 

 

 

 

 

 

 

03

 

“Subnet “ + IP address

 

Same as Menu option 02.

 

 

 

 

 

 

 

04

 

“Gateway “ + IP address

 

Same as Menu option 02.

 

 

 

 

 

 

 

05

 

“DNS Server “ + IP address

 

Same as Menu option 02.

 

 

 

 

 

 

 

07

 

“Preferred Vocoder”

 

Enter “9” to go to the next selection in the list:

 

 

 

 

 

 

1.

PCMU

 

 

 

 

 

 

2.

PCMA

 

 

 

 

 

 

3.

iLBC

 

 

 

 

 

 

4.

G-726

 

 

 

 

 

 

5.

G-723

 

 

 

 

 

 

6.

G-729

 

 

 

 

 

 

 

10

 

“MAC Address”

 

Announces the MAC address of the unit.

 

 

 

 

 

 

 

13

 

“Firmware Server IP Address”

 

Announces current Firmware Server IP address. Enter 12 digit

 

 

 

 

 

 

new IP address.

14“Configuration Server IP Address” Announces current Config Server Path IP address. Enter 12 digit new IP address.

 

15

 

 

 

“Upgrade Protocol”

 

 

Upgrade Protocol for firmware and configuration update. Enter

 

 

 

 

 

 

 

 

“9” to toggle between HTTP, TFTP and HTTPS.

 

 

 

 

 

 

 

16

 

 

 

“Firmware Version”

 

Firmware version information.

 

 

 

 

 

 

 

 

Firmware upgrade mode. Enter “9” to toggle among the

17

 

 

 

“Firmware Upgrade”

 

 

 

 

 

 

 

 

 

following three options:

1. always check

2. check when pre/suffix changes

3. never upgrade

 

47

 

“Direct IP Calling”

 

 

Enter the target IP address to make a direct IP call, after dial

 

 

 

 

 

 

 

tone. (See Make a Direct IP Call section.)

 

 

 

 

 

 

 

 

 

 

Grandstream Networks, Inc.

GXP1100/1105 User Manual

Page 15 of 34

 

 

 

 

Firmware version: 1.0.1.110

Last Updated: 01/2012

Page 16
Image 16
Grandstream Networks GXP11O5 manual Configuration Guide, Configuration VIA IVR Menu, GXP1100/1105 IVR Menu Definitions