Grizzly G0648 manual

5.Press the ON/OFF button. The OPERATING LED will light, and the machine will start momentarily.

6.Observe the digital display and make sure the EXHAUSTING TIME and FILTER ROLLING TIME values are at your last setting, or at least at the factory initial settings for EXHAUSTING TIME, and for FILTER ROLLING TIME.

7.Begin welding, being sure to follow all safety rules.

Note: If the warning lamp/buzzer comes on, it indicates that the rolling-type filter has run out and it is time to replace the roll.

8.When finished welding, press the ON/OFF button, and the machine will wind down slowly until the fan stops.

-18-

Note: After the machine has operated over a minute and then shut down, the FILTER CLEANING lamp will light indicating that as soon as the fan completely stops the vibrat- ing filter will operate in three short durations approximately 3 seconds each.

9.For additional cleaning, manually push and hold the vibrating filter button for a few more seconds to remove any caked-on material.

10.Clean out both the slag and dust drawers.

11.After welding, make it a habit to inspect under the machine and your work area for anything that could smolder and start a fire.

G0648 Welding Fume Extractor

Image 20

Grizzly G0648 owner manual

Contents

Model G0648 Welding Fume Extractor Ss ,EAD from Leadbased PAINTS Table of Contents Contact Info IntroductionForeword Functional Overview Vibrating Filter & Hepa Filter Housing Identification Machine Data Sheet Other Specifications !,7!93 53% !.3 !002/6%$$ 3!&%49 ,!33%33 7%. /0%2!4 !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29 53%3!!2/5.$%$ %84%.3/..#/2$ 2!4%$4&/2/4%-!#.%!-0%2!%2 53%3 2%#/--%.$%$- !##%33/2%3 -!.9 -!#.%3 #!. %*%#4 7/2+0%#%3 4/7!2$ /0%2!4/2 !,7!93 ,/#+ -/,% !3%3 & 53%$ % %&/2% /0%2!4. -!#.%29# Additional Safety Instructions for Welding Fume Extractors Meeting Welding Fume Extraction Codes Standards 220V 3-Phase Operation Circuit Requirements Setup Setup SafetyItems Needed for Setup Unpacking Box 2 Figure Qty InventoryCrate 1 Figure Qty Hardware Recognition Chart Site Considerations Floor Load Ducting Arm Installation To install the ducting armTest Run To test run the machine Completely open both blast gates on the ducting arm Figure To use the machine Operation Safety General OperationOperations Page Control Panel Operation Setting Time Left Button ControlsSetting Time Right Button Controls Changing Rolling Filter Timing To change the rolling-filter timing Model G0648 Rolling Filter Consumption Chart Accessories T20474-First Layer Stainless ScreenT20475-Second Layer Paper Filter Roll T20529-Third Layer Filter H5297 6 Welding Fume Collection Kit H7217-Rigid Flex HoseSteel 6 Elbows G7366 6 G7368 6 G7367 6 G7369 6 90G7370 6 Model T20505 welding respirator H3157-Deluxe Welding Gloves Maintenance CleaningSchedule Lubrication Slag-Screen Cleaning To perform this procedureLong-Term Storage Tools Needed Qty Rolling-Filter Replacement Removing recovery axlePage Vibrating Filter Manual Cleaning Page Page Hepa Filter Manual Cleaning To clean the Hepa filterPage Symptom Possible Cause Possible Solution ServiceTroubleshooting Operation Wiring Electrical Safety Instructions Wiring Overview 220 VAC Main Electrical Box Wiring Main ELE BOX Input relay, fuse bus, phase Controller Transformer Pigtail Main Electrical Box Components Control Panel WiringMAIN ELE Cntrl Control Panel Electrical Components Digital Cabinet Wiring MOT Cabinet Electrical Components Vibrating Parts Main Parts Breakdown Parts List Description Motor 2HP 220V 3PH Blast Gates and Ducting Arm Breakdown Parts List Main Electrical Box Label Placement G0648 Welding Fume Extractor 22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7! Warranty and Returns #ALL 4ODAYD&ORO! &2%%