![](/images/new-backgrounds/1214415/21441539x1.webp)
Mounting |
|
Mounting Sander | Dust Collection |
Once you have confirmed that your machine is running properly, mount it to a workbench.
The strongest mounting option is a "Through Mount" where holes are drilled all the way through the workbench, and hex bolts, washers, and lock nuts are used to secure the sander to the workbench.
����
�����������
������������
�����������
���������
�����������
�����������
��������
Figure 22. Example of a through mount setup.
Another option for mounting is a "Direct Mount" where the machine is simply secured to the workbench with a lag screw.
���������
�����������
������������
��������������
![](/images/new-backgrounds/1214415/21441539xi16.webp)
![](/images/new-backgrounds/1214415/21441539xi17.webp)
![](/images/new-backgrounds/1214415/21441539xi18.webp)
![](/images/new-backgrounds/1214415/21441539xi19.webp)
![](/images/new-backgrounds/1214415/21441539xi20.webp)
![](/images/new-backgrounds/1214415/21441539xi21.webp)
���������![](/images/new-backgrounds/1214415/21441539xi23.webp)
![](/images/new-backgrounds/1214415/21441539xi24.webp)
![](/images/new-backgrounds/1214415/21441539xi25.webp)
![](/images/new-backgrounds/1214415/21441539xi26.webp)
![](/images/new-backgrounds/1214415/21441539xi27.webp)
![](/images/new-backgrounds/1214415/21441539xi28.webp)
![](/images/new-backgrounds/1214415/21441539xi29.webp)
![](/images/new-backgrounds/1214415/21441539xi30.webp)
![](/images/new-backgrounds/1214415/21441539xi31.webp)
![](/images/new-backgrounds/1214415/21441539xi32.webp)
![](/images/new-backgrounds/1214415/21441539xi33.webp)
![](/images/new-backgrounds/1214415/21441539xi34.webp)
![](/images/new-backgrounds/1214415/21441539xi35.webp)
![](/images/new-backgrounds/1214415/21441539xi36.webp)
![](/images/new-backgrounds/1214415/21441539xi37.webp)
![](/images/new-backgrounds/1214415/21441539xi38.webp)
![](/images/new-backgrounds/1214415/21441539xi39.webp)
![](/images/new-backgrounds/1214415/21441539xi40.webp)
![](/images/new-backgrounds/1214415/21441539xi41.webp)
![](/images/new-backgrounds/1214415/21441539xi42.webp)
![](/images/new-backgrounds/1214415/21441539xi43.webp)
![](/images/new-backgrounds/1214415/21441539xi44.webp)
Figure 23. Example of a direct mount setup.
Note: To reduce vibration when operating, keep the rubber cushion included with your sander between the machine base and the workbench.
DO NOT operate the Model H8192 without an adequate dust collection system. This sander creates substantial amounts of wood dust while operating. Failure to use a dust collection system can result in short and
Recommended CFM at EACH Dust Port: 100 CFM
Do not confuse this CFM recommendation with the rating of the dust collector. To determine the CFM at the dust port, you must consider these variables: (1) CFM rating of the dust collector, (2) hose type and length between the dust collector and the machine, (3) number of branches or wyes, and (4) amount of other open lines throughout the system. Explaining how to calculate these variables is beyond the scope of this manual. Consult an expert or purchase a good dust collection
To connect a dust collection hose:
1.Fit a 2" dust hose from the dust collection system over each dust port, and secure them in place with a 2" hose clamp.
2.Tug the hoses to make sure they do not come off.
Note: A tight fit is necessary for proper performance.