Manuals / GTO / Household Appliance / Garage Door Opener

GTO UL325 SERIES installation manual IMPORTANT Deailed Wire Routing Diagrams

Models: UL325 SERIES

1 45

Download 45 pages 5.68 Kb

Page 24

IMPORTANT: Deailed Wire Routing Diagrams

IMPORTANT: Deailed Wire Routing Diagrams

The battery harness wire has an in-line 20 Amp fuse that must be placed inside the opener when connecting the battery to the opener. The il- lustration to the right shows the best placement for the bat- tery harness wire, connector and in-line fuse.

ON/OFF

Receiver Wire

	F
/OF
ON

Battery Harness Wire

Battery Harness

In-Line 20 Amp Fuse

(included)

20

Battery Harness

Connectors

The wires from the battery harness, receiver, transformer or solar panel, and any accessories that have been installed must be routed down the sides of the opener and flatly out the strain relief slot in the back of the opener.

It is IMPORTANT that the wires lay flat and run inside the routing pins at the back of the opener and out the strain relief slot without being pinched when the control board access cover is replaced. See the illustrations to the right and below.

To avoid stripping screw holes - tightening screws by hand with a hand held screwdriver is recommended.

Strain Relief Slot

If you have any questions please call GTO Technical Service at 1-800-543-1236.

MIghty Mule 350	–	ON
	o
Wire Routing		/OFF
Wire Routing

Routing Pin

Neatly arrange all wires to lay flat as they come out of the opener.

Battery Harness Wires

Transformer Wires

Receiver Wires

Accessory Wires

20

Image 24

GTO UL325 SERIES installation manual IMPORTANT Deailed Wire Routing Diagrams

Contents

Installation Manual for the E-Z GATE OPENER UL325 SERIESConverting Temperature When You KnowSymbol When You KnowTable of Contents KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCEImportant Safety Instructions InstallationPLEASE READ THIS FIRST E-Z GATE OPENERSIMPORTANT SAFETY INSTRUCTIONS To Manually Open and Close the Gate, Follow the Procedure BelowDisconnecting the Opener switch is OFF and the gate is NOT movingFor The Consumer Entrapment Zones for a Pull-To-Open ApplicationIMPORTANT SAFETY INSTRUCTIONS I. Before InstallationNEVER INSTALL any control device within gray area Pull-To-Open ApplicationIMPORTANT SAFETY INSTRUCTIONS II. During InstallationIMPORTANT SAFETY INSTRUCTIONS III. After InstallationENTRAPMENT ALARM UL 325 30A.1.1A Secondary Means of Protection Against EntrapmentIMPORTANT SAFETY INSTRUCTIONS Leading Edge Contact Sensor on both sides of the gateRequired Safety Precautions for Gates Install Warning SignsEntrapment Protection Warning SignsIMPORTANT SAFETY INSTRUCTIONS Logo and warning labels 2 installed on each side of opener housingProduct identification label 1 installed under rear mount on arm 1. Turn opener power switch OFFHardware Bag Contents Tools Needed Technical Specifications POWERMIGHTY MULE 350 E-Z GATE OPENER DRIVEInstallation Overview Preparation of the GatePull-to-Open Gates Gate Opens into the Property StepInstallation of Mounting Hardware Recommended Reinforcement Examplesof the Post Bracket Assembly and the Gate Bracket Determining the Mounting PositionPost Bracket Assembly StepStep 2 minimumCLOSED POSITION Gate in the OPENED POSITION 2 minimumInstalling the Post Bracket Assembly and Gate Bracket Gate Bracket Mounting ExamplesPost Bracket Assembly StepInstallation of the Closed Position Stop Mounting the OpenerStep StepPreparing to Activate the System Check ListPowering the System Solar Panel and Gate Acticity ChartNEVER USE TRANSFORMER AND SOLAR PANELS AT THE SAME TIME it willl damage the control boardConnecting the Battery StepStep StepIMPORTANT Deailed Wire Routing Diagrams Connecting the Transformer IMPORTANT INFORMATION ABOUT LOW VOLTAGE WIREto protect wire from lawn mowers and weed eaters StepLow Voltage Wire from Transformer Make sure the exposed wires do not touch each otherStep StepCONTROL BOARD SETTINGS Connecting Solar PanelsDIP Switches Main DIP Switch Settings MODESSetting the Closed Position Limit For PULL-TO-OPEN Installation Turn the power switch onYour Mighty Mule 350 has two Limit Settings 2 CLOSED Limit settingObstruction Sensitivity Potentiometer Setting Setting Auto-Close TimeALWAYS KEEP SAFETY AT THE TOP OF YOUR LIST WHEN ADJUSTING OR SERVICING YOUR AUTOMATIC GATE OPENERSetting Your Personal Transmitter Code 2. Set the transmitter DIP Switches1. Remove the Transmitter Cover 3. “Teach” the New Code to Control Board MemoryInstalling the Receiver NOTE Do not mount upside downRun the cable through PVC conduit to protect it from damage Connecting Additional Safety Devices Contact Sensors safety edgesIf not installing a contact sensor skip to next section Call GTO Sales at 1-800-543-4283 for information on compatibleNon-Contact Sensors photo beams Exit LoopIf not installing a non-contact sensor skip to next section If not installing a shadow loop skip to next sectionConnecting Accessories Automatic Gate Lock FM143Wiring the A utomati c Gate Lock If not connecting accessories skip to next sectionMighty Mule Free Entry/Exit Loop Wiring Driveway Loops to the Mighty MuleWhen everything has been connected to the opener FINAL STEPMighty Mule Gate Opening Sensor FM138 Push to Open Installation Determining The Mounting Position of The Post Bracket AssemblyPost Bracket Assembly Swinging gates shall not open into public access areasSetting the Open Position Limit StepStep StepTESTING YOUR OPEN LIMIT SETTING CLEARING PROGRAMMED OPEN LIMIT SETTINGStep StepMaintenance & Troubleshooting Guide 3. 1 beep when attempt to run the unit No battery is connected6. Power-Cycle 1. 1 beep with 2 seconds offThe Gate CLOSES Then Opens Again on its Own The Gate OPENS Then Closes Again on its Own3. POWER LED Green 2. STATUS LED LED1 While the unit is IDLE 1 blink with 2 seconds offRepair Service 1-800-543-GATEE-Mail techsupport@gtoinc.com For technical service Call toll freeColumn Installation Information Column Mount ExampleA + B can not exceed 14 inches Pivot BracketACCESSORIES Accessories are Available From Your Retail StoreWireless Entry Intercom / Keypad FM136 E-Z GATE OPENERSIf you have a question about any special order item just call 1-800-543-GATEAccessories are Available From Your Retail Store cont Low Voltage Wire RB509