Section 7
DIAGNOSTIC TESTS
8.Crank engine again and see if fuel is coming out of the fuel lines.
RESULTS:
1.If no fuel is noted in Steps 3 or 8, replace fuel injector pump. (Reinstallation of all original shims will be required.)
2.If fuel is noted, proceed to next step in flowchart.
TEST 37 - CHECK ENGINE / CYLINDER LEAK
DOWN TEST / COMPRESSION TEST
GENERAL:
Most engine problems may be classified as one or a combination of the following:
•Will not start.
•Starts hard.
•Lack of power.
•Runs rough.
•Vibration.
•Overheating.
•High oil consumption.
DISCUSSION:
The Cylinder Leak Down Tester checks the sealing (compression) ability of the engine by measuring air leakage from the combustion chamber. Compression loss can present many different symptoms. This test is designed to detect the section of the engine where the fault lies before disassembling the engine.
PROCEDURE:
1.Remove a fuel injector.
2.Gain access to the flywheel. Remove the valve cover.
3.Rotate the engine crankshaft until the piston reaches top dead center (TDC). Both valves should be closed.
4.Lock the flywheel at top dead center.
5.Attach cylinder leak down tester adapter to spark plug hole.
6.Connect an air source of at least 90 psi to the leak down tester.
7.Adjust the regulated pressure on the gauge to 80 psi.
8.Read the right hand gauge on the tester for cylinder pressure. 20 percent leakage is normally acceptable. Use good judgement, and listen for air escaping at the carburetor, the exhaust, and the crankcase breather. This will determine where the fault lies.
9.Repeat Steps 1 through 8 on remaining cylinder.
RESULTS:
•Air escapes at the air intake chamber – check intake valve.
•Air escapes through the exhaust – check exhaust valve.
•Air escapes to the crankcase – check piston rings.
•Air escapes from the cylinder head – the head gas- ket should be replaced.
CHECK COMPRESSION:
Lost or reduced engine compression can result in (a) failure of the engine to start, or (b) rough operation. One or more of the following will usually cause loss of compression:
•Blown or leaking cylinder head gasket.
•Improperly seated or
•Worn Piston rings or cylinder. (This will also result in high oil consumption).
NOTE: It is extremely difficult to obtain an accu- rate compression reading without special equip- ment. For that reason, compression values are not published. Testing has proven that an accu- rate compression indication can be obtained using the following method.
PROCEDURE:
1.Remove fuel injectors.
2.Insert a compression gauge into one of the cylinders.
3.Crank the engine until there is no further increase in pressure.
4.Record the highest reading obtained.
5.Repeat the procedure for the remaining cylinder and record the highest reading.
RESULTS:
The difference in pressure between the three cylin- ders should not exceed 25 percent. If the difference is greater than 25 percent, loss of compression in the lowest reading cylinder is indicated.
Example 1: If the pressure reading of cylinder #1 is 165 psi and of cylinder #2, 160 psi, the difference is 5 psi. Divide "5" by the highest reading (165) to obtain the percentage of 3.0 percent.
Example 2: No. 1 cylinder reads 160 psi; No. 2 cylin- der reads 100 psi. The difference is 60 psi. Divide "60" by "160" to obtain "37.5" percent. Loss of compression in No. 2 cylinder is indicated.
If compression is poor, look for one or more of the fol- lowing causes:
•Loose cylinder head bolts.
•Failed cylinder head gasket.
•Burned valves or valve seats.
•Insufficient valve clearance.
•Warped cylinder head.
•Warped valve stem.
•Worn or broken piston ring(s).
•Worn or damaged cylinder bore.
•Broken connecting rod.
•Worn valve seats or valves.
•Worn valve guides.
Page 54
