Hague Quality Water Intl 60 SERIES manual

Iron Filter and Potassium Feeder Installation Guide

Important: The 61AAN is capable of treating a combination of undesirable constituents in the water (iron, manganese, and/or hydrogen sulfide). However, the filter must be applied within the operating limits stated in the WaterMax® Filter Specifications in this manual. Failure to comply with these specifications will degrade performance and possibly cause the control valve to malfunction.

Note: The iron filter should be installed after the pressure tank or water meter and before the water heater or any water softener appliance, unless otherwise recommended. See Figure 6. A minimum 3/4" pipe is required for proper function of the filter. Examine the inlet piping to make sure the pipe is not plugged with lime or iron. If the piping is plugged, it must be cleaned or replaced.

Figure 6: Iron Filter and Potassium Feeder Placement

Installation Tip: To install the filter, follow steps 1–10 of Installation Steps and Start-Up Procedures, excluding Step 4—Connect the Brine Tank. Instead, connect the potassium permanganate feeder as outlined on the following page.

Caution: Do not adjust the float assembly. This feeder is preset for a 4-ounce feed of potassium permanganate. Use care when working with potassium permanganate. Follow instructions printed on the cover of the feeder as well as the instructions on the potassium permanganate container.

WaterMax 60 Series Owner’s Manual

11/10/2008

25

Image 25

Hague Quality Water Intl 60 SERIES manual Iron Filter and Potassium Feeder Installation Guide

Contents

Series Number Owner Pays for Year Limited Warranty Contents For Owner’s Reference General Information Six-Button Controller Getting Maximum Efficiency From the Appliance Controller Part Function Six-Button Controller, Set Time of Day Customer SettingsSet Regeneration Time Set Number of People Iron Type Description Checklist Before Installation Do Not Precautions Prepare the Placement Area Installation Steps and Start-Up Procedures Installation Steps and Start-Up Procedures, Check for Leaks Set Up the ControllerPlug in the Transformer Add Water to the Brine Tank Bypass Valve Complete the Installation Blending Valve Setting and Using the ControllerRegenerate Button Meaning Possible Values Comments Service Settings Display Meaning Possible Values Comments Service Settings, See 72-96 Hour Operating Modes Mode 1-Timer Mode 62AKQ Mode 1 Timer Mode Setting Chart NA, See Mode 1 Setting Chart Mode 2 Demand Delayed Mode Setting Chart Modes 1 Salt Depths Replenishment Procedure 62AJQ Replenishment ProcedureTools and Materials Needed Add Replenishment Media 62AJQ Replenishment Procedure,Refill Tank With Water Replace Fill Plug Regeneration Cycle Frequency Worksheet 61AAN WaterMax Iron Filter Sizing FormulaDetermine Monthly Usage Water Example Iron Filter and Potassium Feeder Placement Iron Filter and Potassium Feeder Installation Guide Start-Up Procedures for 4-oz Potassium Permanganate Feeder Cabinet and Cover Assemblies Assembly and PartsIncorrect Correct Brine Tank Assembly Assembly and Parts, Description Quantity Cabinet and Assemblies Injector Assembly Injector Assembly Screen 93810 Injector93223 Injector Throat Bypass Assembly Bypass Assembly Piston Assembly HousingSensor Wire Assembly Drive End Cap Assembly Drive End Cap Assembly 90217 Valve HousingDrive Motor 93238 Drive Gear Concave side Static O-Ring Brine Valve Housing Assembly 90843 0.5 gpm BrineFlow Control End Cap H2086 Drain Line Drain End Cap AssemblyRetainer Safety Shutoff Assembly Safety Shutoff Assembly Safety Shutoff Valve Elbow Installation Safety Shutoff Valve Elbow Installation Fill Plug Fill Plug Assembly Problem Possible Cause Solution Troubleshooting Troubleshooting, Efficiency Statements Reading Model NumbersNumber or Letter Letter Media Type Series 63MAQ1 63BEQ1,2 63MXQ1 WaterMax Water Conditioner Specifications62AMQ1 62APQ1 62AJQ3 Filter Purpose WaterMax Filter Specifications Certificates Certificates, Certificates, Page Page Series