3800/3900 User’s Guide | Hand Held Products specs

Turbo Mode: The scanner sends characters to an IBM AT terminal faster. (For use with IBM AT only.) If the terminal drops characters, do not use Turbo Mode. Default = Off

Turbo Mode On

* Turbo Mode Off

Numeric Keypad Mode: Sends numeric characters as if entered from a numeric keypad. Default = Off

Numeric Keypad Mode On

* Numeric Keypad Mode Off

Automatic Direct Connect: Use this selection if you are using a laptop whose keyboard is disabled when you plug in the scanner. This selection can also be used if you have an IBM AT style terminal and the system is dropping characters. Default = Off

Automatic Direct

Connect Mode On

* Automatic Direct Connect

Mode Off

3800/3900 User’s Guide

2 - 7

Image 33

Hand Held Products manual 3800/3900 User’s Guide

Contents

User’s Guide Disclaimer Statement of Agency Compliance FCC Class B Compliance StatementCanadian Notice UL and cUL Statement LED Safety StatementTÜV Statement TIC Statement Table of Contents Output Data Formatting Code 93 Message Length Check Digit Addenda Addenda Required Addenda Separator Cloning Maintenance Viii Getting Started Typical Applications forAbout This Manual Or an Unpacking the Scanner Scanner Bottom View Scanner Identification Connecting the Scanner When Powered by Host Keyboard Wedge For Mounting Information Plug and PlaySpecular Zone Option Setting IBM 4683 Ports 5B, 9B, and 17 Interface USB Interface Symbology Suffix 3800/3900 User’s Guide Symbology Prefix Ocia InterfaceNCR Ocia Short Format 8 Bit Interface NCR Ocia Long Format 9 Bit Interface SymbologyNixdorf Ocia Interface Serial Wedge 3800/3900 User’s Guide 3800/3900 User’s Guide Keyboard Wedge Connection Terminal Interfaces Terminal ID Terminal Models Terminal ID Supported Terminals Supported Terminals Keyboard Country Keyboard StyleCountry Code Scan Keyboard Modifiers 3800/3900 User’s Guide Serial Port Connection Baud Rate RS-232 Word Length Data Bits, Stop Bits, and Parity RS-232 Word Length Data Bits, Stop Bits, and Parity Wand Emulation Connection RS-232 Handshaking Wand Emulation Transmission Rate Wand Emulation Idle Wand Emulation Polarity Data Block Size Delay Between Blocks Overall Checksum Beeper Volume OutputScan Rate Beeper Tone Scan VotingReduce Quiet Zone Reread Delay Trigger Mode Good Read Delay Serial Trigger Time Out 3800/3900 User’s Guide Data Editing Scan the Add Prefix or Add Suffix symbolPrefix/Suffix Overview Points to Keep In Mind Scan the Clear One Prefix or Clear One Suffix symbol To Clear One or All Prefixes or SuffixesScan Add Suffix To Add a Carriage Return Suffix to all Symbologies Suffix Selections Prefix Selections Symbology Code Symbology ChartHex Symbology Code Hex Dec Hex Char Ascii Conversion Chart Code Intercharacter, Interfunction, and Intermessage Delays Intercharacter DelayFunction Code Transmit User Specified Intercharacter Delay Intermessage Delay Interfunction Delay 3800/3900 User’s Guide Data Formatting Scan the Enter Data Format symbol Primary/Alternate FormatData Format Editor Introduction To Add a Data Format Other Programming Selections Data Format Editor Commands Move Commands Data Format Editor Alternate Data Formats Data Formatter 3800/3900 User’s Guide Secondary Interface Secondary Code 39 Wand EmulationSecondary RS-232 Connection Secondary Non Decoded Output Laser Emulation Non Decoded Output Laser Emulation Transmission RateNon Decoded Output Laser Emulation Polarity Secondary Trigger Mode Non Decoded Laser Emulation IdleDisabling the Secondary Interface 3800/3900 User’s Guide Symbologies All SymbologiesIntroduction Message Length Description Start/Stop Characters Codabar Check Character Concatenation Codabar Message LengthCodabar Code Code 39 Message Length Base Code 39 Append Full Ascii Check Digit Interleaved 2 Strict Decoding Interleaved 2 of 5 Message Length Code 93 Message Length Code 2 Iata Code 2Code 2 of 5 Message Length Iata Code 2 of 5 Message Length Matrix 2 Matrix 2 of 5 Message Length Check Digits Required Code 11 Message Length GS Substitution Code 128 Message Length Telepen Telepen Message Length Telepen Output Number System UPC a AddendaAddenda Required UPC Strict Decoding Addenda Separator UPC E Expand UPC E0 and UPC E1 UPC E Addenda Addenda Separator EAN/JAN EAN/JAN Isbn Enable Default All EAN/JAN 8 Settings Addenda Addenda Separator MSI MSI Message Length Plessey Message Length Plessey RSS Limited RSS-14 RSS Expanded Message Length RSS Expanded China Post Message Length China Post Code Off Minimum Message Length Maximum Message Length Show GLI Blocks Scan Diagnostics 3800/3900 User’s Guide Minimum Message Length Maximum Message Length Eanucc Composite Symbology Enable UPC/EAN VersionEanucc Composite Eanucc Composite Code Message Length 3800/3900 User’s Guide Cloning Procedure 3800/3900 User’s Guide Installing Visual Menu from the Web Temporary Visual Menu ConfigurationVisual Menu Visual Menu Introduction Upgrading USB Firmware Interface Keys Keyboard Function RelationshipsFunction Code HEX/ASCII Value Full Ascii Ctrl + Country Codes IBM AT/XT Supported Interface KeysPS/2 Compatibles IBM XTs IBM, DDC, Memorex Interface Keys Compatibles Telex, Harris SYN PF1 ETB PF2 Can PF3 PF4 SUB PF5 ESC PF6 PF7 PF8 PF9 Memorex Telex Ansi Ascii Esprit 200 Interface Keys Supported Interface Keys Apple Mac/iMac Utilities To Add a Test Code I.D. Prefix to All SymbologiesShow Software Revision Show Data Format Specular Effect Reduction Serial Programming Commands Menu Command SyntaxConventions Query Commands Concatenation of Multiple CommandsResponses Examples of Query Commands Resetting the Factory Settings Trigger Commands Setting Serial Selection Command Menu Commands WNDPAT0 Output Selections Data Formatter Selections Prefix/Suffix Selections Selections Symbologies CBRSSX0 I25STR0 Teldft UPAARQ0 UPAARQ1 E13ARQ0 Plsdft Mpddft Product Specifications Product SpecificationsParameter Specification Product Specifications Laser StandardCable Pinouts Compatible Standard Cable Pinouts WandEmulation Serial Output Standard Cable Pinouts Primary Interface Cables USB Standard Cable Pinouts 3800/3900 User’s Guide Maintenance MaintenanceCleaning the Scanner’s Window Inspecting Cords and Connectors Troubleshooting Replacing the Interface CableTo Replace the Interface Cable Is the scanner having trouble reading your symbols? 3800/3900 User’s Guide Customer Support Product Service and Repair Technical Assistance Online Product Service and Repair AssistanceAsia Pacific Japan Online Technical Assistance Limited Warranty 3800/3900 User’s Guide 3800/3900 User’s Guide Page Page Page Sample Symbols Matrix 2 Programming Chart Save Discard Hand Held Products, Inc