Hand Held Products Dolphin 7400, Dolphin 7450 specification

ActiveSync Connection Settings

To configure the Dolphin 7400/7450 terminal for communications, see the previous section on Configuring the Dolphin Terminal.

Setting Up For Communications With The USB HomeBase

To use the USB HomeBase, you need the following equipment:

•USB HomeBase with power supply

•USB Cable

•CD with USB-IrDA drivers

•Windows 98, Windows Me or Windows 2000 computer.

Note: The USB HomeBase does not support Windows NT

To install the USB HomeBase, follow these steps:

1.Plug in the power supply and connect it to the back of the USB HomeBase.

2.Plug the USB cable into the back of the USB home base.

3.Plug the other end of the USB cable into your PC.

At this point, a dialog box appears on your PC instructing you that the system has detected new hardware and it is searching for the HHP USB-IrDA driver. Unless you have previously installed the USB HomeBase, the OS will be unable to find one and the Found New Hardware Wizard screen shown below will display on your PC’s screen.

6 - 12

Image 62

Hand Held Products Dolphin 7400, Dolphin 7450 manual Setting Up For Communications With The USB HomeBase

Contents

Dolphin 7400/7450 Hand Held Computer Disclaimer PatentsTrademarks Table of Contents Using the Dolphin 7400/7450 Dolphin QuadCharger 11-2 Additional Features Introduction Required Safety Labels Batch Terminals If Your Dolphin 7400/7450 has a Radio Canadian Compliance FCC Compliance Dolphin 7400/7450 Batch TerminalDolphin 7400/7450 RF Terminal with Cisco Regulatory and Safety Agency Approvals Parameter Specification Dolphin 7400/7450 RF Cisco 352 R&TTE Compliance Statement TTE Microwaves Care and Cleaning of the DolphinBatteries Page Dolphin 7400 Models and Options Accessories for the Dolphin 7400/7450Getting Started Using Dolphin 7400/7450 for the First Time Bar Code Symbologies SupportedLaser Engine Options and Symbologies Supported Unpack the Carton and Check Its Contents Installing the Battery Pack Charging the Main Battery and Backup BatteryRemoving the Battery Pack Turning the Dolphin On And Off For the First Time Waking the Dolphin From Sleep Mode Do not Press ANY Keys While the Terminal is Booting UP Stylus Properties Screen Setting the Date/Time Using DetectoidPC and DetectoidCE Setting Up Communications with DetectoidInstalling DetectoidPC Page DetectoidCE Touchscreen-equipped terminals Configuring the ModemVerifying that Dolphin 7400/7450 is Working Properly Terminals without touchscreens Resetting the Dolphin Cold BootResetting the Dolphin Warm Boot Page System Features Dolphin 7400/7450 Overview VGA Display Front Panel FeaturesLEDs Cursor Keys Audio SignalsON/SCAN Key Keyboard Image Engine Back Panel FeaturesDolphin Laser Engine Battery WellBattery Charging Contacts Hand Strap Bumpers Communication Power Managing Battery Power CriticalBatt=dworda Setting Critical and Low Battery PointsUsing the Power Control Panel LowBatt=dword19 Using the Battery Conditioning Utility Charging the Battery PackServicing the Battery Pack Storing Batteries Entering Data Using the Dolphin 7400/7450Using the Image Reader Via the Touch Screen Omni-Directional Scanning Options Linear bar code 2D Matrix symbolReading a Bar code Capturing Images Communication Media Software Communication Programs Using the Special Keys Keyboards Using the Cursor Keys To Use This Cursor Key Press Description Using the Modifier Keys Other Special Keys Navigating the Keyboard Key Combinations Using the Modem Dolphin 7400/7450 RF Terminal Configuring The Dolphin 7400/7450 RF Terminal Client Utilities for the Cisco Dsss 802.11b Radio Configuring the Cisco Dsss Wlan Radio To Configure the Radio Card Host Connectivity Customizing the ActiveSync Remote IconPage Hub of the System Power ConditioningDolphin Charging/Communication Cradles Ir/IrDA Optical Communications Orange LED HomeBase/IntelliBase/USB HomeBaseGreen LED Data is being sent from the Dolphin HomeBase Green LED AUX Battery LED Description Orange LEDIntelliBase+ Comm LED Description Red LED Back Panel HomeBase/IntelliBase IntelliBase+ USB HomeBase Bottom Panel of HomeBase/IntelliBase/IntelliBase+ Powering the Dolphin Terminal Installing The Charging/Communication Cradle Setting Up For CommunicationsCharging Additional Battery Packs in the IntelliBase+ Deep-Cycling Batteries IBM AT DB9 IBM XT Configuring the Dolphin Terminal for Communications Select StartSettingsControl PanelCommunications PropertiesPage Setting Up For Communications With The USB HomeBase Page Communicating with the Dolphin Terminal Wall Mounting Mounting the HomeBase/IntelliBase/USB HomeBaseDesk Mounting Page Top Panel Dolphin QuadChargerDolphin QuadCharger Parts and Function Inserting and Removing Battery Packs Setting Up The QuadChargerSupplying Power To The QuadCharger Charging Batteries In The QuadCharger Description Status LED Troubleshooting Problem Issue Dolphin Mobile Charging/Communication Cradles Mobile IntelliBase and Mobile Base Parts and Functions Front Panel Dolphin Mobile IntelliBase/Mobile Base Mounting Bracket Power Supply RS-232 Connector Locking Lever RS-232 Bottom Panel of Mobile IntelliBase/Mobile Base Charging a Dolphin Terminal Installing The Dolphin Mobile IntelliBase Mounting the Mobile IntelliBase Spring Arm Assembly Installing The Dolphin Mobile Base Setting the Baud Rate Configuring the Dolphin Terminal Select StartSettingsControl PanelCommunication Settings Developing Applications Page How Problems Should Be Handled Warranty, Support and ServiceLimited Warranty Locations How To Extend Your WarrantyReturn Information North America/Canada Technical AssistanceAssistance Online Europe, Middle East, and AfricaPage Press Appendix aWindows Keyboard Shortcuts Key Combination Function/Special Character Using the Modifier KeysKey Alpha/Numeric Keyboard Red key + T Red key + U Red key + W Red key + Y Key Numeric/Alpha Key Full Alpha Numeric Key/Key Combinations Function/Special Characters ALT + 3 + F12 Red key + P F16 Red key + Q F17 Hold the ALT key down as you type in the numbers HHP, Inc