Manuals / Hearth and Home Technologies / Kitchen Appliance / Egg Cooker

Hearth and Home Technologies BH 105 Introduction, Save These Instructions, Table Of Contents

Models: BH 105

1 49

Download 49 pages 25.25 Kb

Page 4

Introduction

Introduction

Table Of Contents

Warranty	5
Assembly	6
Venting	9
Installation	12
Operation	23
Maintenance	30
Troubleshooting	34
Atmospheric Conversion	35
Service Parts	36
Specifications	42
Wiring Diagram	43
Testing Label	45

Quick Reference Start-Up Back Cover

Appliance Certification.

Model: Pellet Burning Boiler - BH105

Test Lab: Omni-Test Laboratories, Inc.

Report #: 135-S-16-6

Type: Pellet Fueled Central/Supplementary For Residential Use

Standard(s): CAN/CSA B366.1-M91, and UL 391

Note: This appliance is also approved for installation into a shop.

WARNING! RISK OF FIRE! Hearth & Home Technologies disclaims any responsibility for, and the warranty and agency listing will be voided by the following actions:

DO NOT:

•Install or operate a damaged appliance

•Modify the appliance

•Install other than as instructed by Hearth & Home Technologies

•Operate the appliance without fully assembling all components

•Overfire the appliance

•Install any component or part not approved by Hearth & Home Technologies

Improper installation, adjustment, alteration, service, or maintenance can cause injury or property damage. For assistance or additional information, consult a qualified installer, service agency or your dealer.

Please read this entire manual before you install and use your new

boiler. Failure to follow instructions may result in property damage, bodily injury, or even death.

SAVE THESE INSTRUCTIONS

Hearth & Home Technologies, Inc.

352 Mountain House Road

Halifax, PA 17032

4

Image 4

Hearth and Home Technologies BH 105 Introduction, Please read this entire manual before you install and use your new

Contents

Installation & Operating Manual SAFETY NOTICEThe BH 105 Pellet Boiler save these instructionsPage Parts Locations Please read this entire manual before you install and use your new IntroductionSAVE THESE INSTRUCTIONS Table Of ContentsWarranty ECO-CHOICE LIMITED WARRANTYAssembly Boiler Kit Materials Refer to pageDesign AssemblyFloor Protection INSTALLATION IS TO BE PERFORMED BY A QUALIFIED INSTALLER AssemblyNOTE All installation clearances and restrictions must be adhered to Venting Venting Avoid venting into alcove locationsVentingti g Venting Installation INSTALLATION IS TO BE PERFORMED BY A QUALIFIED INSTALLERNOTE All installation clearances and restrictions must be adhered to Keep combustibles away from flue outletInstallation Outside AirHeat Reclaiming Ventilation System HRV NOTE The inlet cover should not be placed in anMain Wiring Installation InstallingInstallationDuct Installing Duct/AirInstallationConditioning Installation RECOMMENDED INSTALLATION INSTRUCTIONS FOR THE PROPEREXAMPLE OF TYPICAL TANKLESS DOMESTIC HOT WATER PIPING EXAMPLES OF TYPICAL DOMESTIC HOT WATER STORAGE PIPINGInstallation SENSING BULBSHUT-OFF VALVE AIR SCOOPInstallation Over Heat Safety Zone Power Failure / Heat Dissipation LoopA POWER FAILURE HEAT DISSIPATION LOOP EXAMPLE OF PIPING IN ACCORDANCE WITH CAN/CSA-B366.1Installation The ControlFirebox Door Fuel Specifications Fuel and Fuel StorageOperation Max Temp dialWATER TEMPERATURE NOTE Pellet Boiler Outdoor Air Reset Operation Graph located on pageWithout the Outdoor Air Temperature Sensor Installed OperationPellet Boiler Outdoor Air Reset Operation OperationOperation 1. Turn Mode Selector to “OFF”Starting A Fire Automatically WATER TEMPERATURE 5. Turn Feed Adjuster to #46. Flip the Igniter Switch up into the “AUTO” position OperationOperation 9. Fill hopper with pellets and remove ashes as required Type of FuelLighting A Fire Manually Follow steps 1 through 5 of the instructions for automatic lighting11. Apply starting gel as shown in Fig.15 Operation12. Light The Starting Gel With A Match 13. Close The Doors Maintenance Burnpot CleaningCleano ut cover Cleaning the Burnpot Air ChamberMaintenance Routine cleaning of heat exchangers and venting is requiredWarning! Risk of Fire Ash, soot or creosote build-up may cause overheating or fireMaintenance Cleaning StepsCombustion Blower Cleaning MaintenanceCleaning the Tube Heat Exchangers Troubleshooting Helpful HintsFuel Cleaning Burn PotAtmospheric Conversion bh105 Stocked#8 Ash base Assembly bh105Cleanout Rod Repair Kit bh1051-00-72210 Scraper Rod Guide#28 Feeder Assembly bh10528.1 28.16bh105 #29 boiler Kit#30 water Plate Kit #31 handle Kitbh105 StockedScrew, #8-18 x 1/2 Hex washer Head Self Drilling Zinc #2 Pt washer, #10-16 x 3/4 hex head TEKS 3 SdS Climaseal PlatedBTU Input Range= 0, and 9350 to 113,900 SpecificationsElectrical 120 VAC 60 Hz Wiring DiagramPELLET BOILER WIRING DIAGRAM Power Failure Backup Supply When current is present, will keep UPS inReady mode POWER FROM THE UPS / This plugsTesting Label BH105BH105 WARNING Risk of fire - Do not operate with the flue draftService Record / Notes Date Of ServiceDescription Of Service Performed ByProudly Printed On 100% Recycled Paper See the section on Maintenance for more details about cleaning Quick Reference Auto-Light1 Turn Mode Selector to OFF 2 Use heat exchanger cleanout rods to clean the heat exchanger tubesSignature of Boxer