Manuals / Hearth and Home Technologies / Kitchen Appliance / Egg Cooker

Hearth and Home Technologies BH 105 manual bh105, Stocked

Models: BH 105

1 49

Page 36

	Service Parts	bh105

	bioﬂow hydronic 105k Pellet boiler	beginning manufacturing date: july 2009
	bioﬂow hydronic 105k Pellet boiler	Ending manufacturing date: Active
		Ending manufacturing date: Active

1
2
3	28	27
		27
4		26
4
5
6		25	24	23		22
			24				21

7
7	8						20
		9					20


		10					19
		11					19
		11
		12
							18
		13		14
					15		17
					15		16
							16

IMPORTANT: THIS IS DATED INFORMATION. when requesting service or replacement				Stocked
parts for your appliance please provide model number and serial number. All parts listed				Stocked
in this manual may be ordered from an authorized dealer.				at depot
ITEm	dESCrIPTION	COmmENTS	PArT NumbEr
1	Hopper Assembly		1-10-72140A
	Gasket, Hopper Throat		3-44-677185	Y
	Hopper Lid Spring Latch		3-31-00927	Y
2	Control Board Plate, Studded w/label		1-10-07330
3	Control Board		1-00-06143	Y
	Control Knob/Shaft	25 Sets	1-00-015605	Y
	Fuse, 6 AMP	Pkg of 5	3-20-49447-5	Y
4	Feeder Cover Assembly		2-00-72158B
5	Differential Switch		3-20-6866	Y
6	Red Nylon Knob		3-31-72196
7	Swing Plate Assembly		1-10-72153A

Additional service part numbers appear on following page.

04/12

Page 36

Image 36

Hearth and Home Technologies BH 105 manual bh105, Stocked

Contents

Installation & Operating Manual SAFETY NOTICEThe BH 105 Pellet Boiler save these instructionsPage Parts Locations Please read this entire manual before you install and use your new IntroductionSAVE THESE INSTRUCTIONS Table Of ContentsWarranty ECO-CHOICE LIMITED WARRANTYAssembly Boiler Kit Materials Refer to pageAssembly DesignFloor Protection Assembly INSTALLATION IS TO BE PERFORMED BY A QUALIFIED INSTALLERNOTE All installation clearances and restrictions must be adhered to Venting Venting Avoid venting into alcove locationsVentingti g Venting Installation INSTALLATION IS TO BE PERFORMED BY A QUALIFIED INSTALLERNOTE All installation clearances and restrictions must be adhered to Keep combustibles away from flue outletInstallation Outside AirHeat Reclaiming Ventilation System HRV NOTE The inlet cover should not be placed in anMain Wiring Installation InstallingInstallationDuct Installing Duct/AirInstallationConditioning Installation RECOMMENDED INSTALLATION INSTRUCTIONS FOR THE PROPEREXAMPLE OF TYPICAL TANKLESS DOMESTIC HOT WATER PIPING EXAMPLES OF TYPICAL DOMESTIC HOT WATER STORAGE PIPINGInstallation SENSING BULBSHUT-OFF VALVE AIR SCOOPInstallation Over Heat Safety Zone Power Failure / Heat Dissipation LoopA POWER FAILURE HEAT DISSIPATION LOOP EXAMPLE OF PIPING IN ACCORDANCE WITH CAN/CSA-B366.1The Control InstallationFirebox Door Fuel Specifications Fuel and Fuel StorageOperation Max Temp dialWATER TEMPERATURE NOTE Pellet Boiler Outdoor Air Reset Operation Graph located on pageWithout the Outdoor Air Temperature Sensor Installed OperationPellet Boiler Outdoor Air Reset Operation Operation1. Turn Mode Selector to “OFF” OperationStarting A Fire Automatically WATER TEMPERATURE 5. Turn Feed Adjuster to #46. Flip the Igniter Switch up into the “AUTO” position OperationOperation 9. Fill hopper with pellets and remove ashes as required Type of FuelLighting A Fire Manually Follow steps 1 through 5 of the instructions for automatic lightingOperation 11. Apply starting gel as shown in Fig.1512. Light The Starting Gel With A Match 13. Close The Doors Maintenance Burnpot CleaningCleano ut cover Cleaning the Burnpot Air ChamberMaintenance Routine cleaning of heat exchangers and venting is requiredWarning! Risk of Fire Ash, soot or creosote build-up may cause overheating or fireMaintenance Cleaning StepsMaintenance Combustion Blower CleaningCleaning the Tube Heat Exchangers Troubleshooting Helpful HintsFuel Cleaning Burn PotAtmospheric Conversion bh105 Stocked#8 Ash base Assembly bh105Cleanout Rod Repair Kit bh1051-00-72210 Scraper Rod Guide#28 Feeder Assembly bh10528.1 28.16bh105 #29 boiler Kit#30 water Plate Kit #31 handle Kitbh105 StockedScrew, #8-18 x 1/2 Hex washer Head Self Drilling Zinc #2 Pt washer, #10-16 x 3/4 hex head TEKS 3 SdS Climaseal PlatedSpecifications BTU Input Range= 0, and 9350 to 113,900Electrical 120 VAC 60 Hz Diagram WiringPELLET BOILER WIRING DIAGRAM Power Failure Backup Supply When current is present, will keep UPS inReady mode POWER FROM THE UPS / This plugsTesting Label BH105BH105 WARNING Risk of fire - Do not operate with the flue draftService Record / Notes Date Of ServiceDescription Of Service Performed ByProudly Printed On 100% Recycled Paper See the section on Maintenance for more details about cleaning Quick Reference Auto-Light1 Turn Mode Selector to OFF 2 Use heat exchanger cleanout rods to clean the heat exchanger tubesSignature of Boxer

1
2
3	28	27
		27
4		26
4
5
6		25	24	23		22
			24				21

7
7	8						20
		9					20


		10					19
		11					19
		11
		12
							18
		13		14
					15		17
					15		16
							16

1
2
3	28	27
		27
4		26
4
5
6		25	24	23		22
			24				21

7
7	8						20
		9					20


		10					19
		11					19
		11
		12
							18
		13		14
					15		17
					15		16
							16

1
2
3	28	27
		27
4		26
4
5
6		25	24	23		22
			24				21

7
7	8						20
		9					20


		10					19
		11					19
		11
		12
							18
		13		14
					15		17
					15		16
							16