Safety Alert Key:
•DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.
•WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.
•CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
•NOTICE: Used to address practices not related to personal injury.
Table of Contents
A. | Congratulations | 2 |
B. | Limited Lifetime Warranty | 5 |
1 Listing and Code Approvals
A. | Appliance Certification | 6 |
B. | Tempered Glass Specifications | 6 |
C. | BTU Specifications | 6 |
D. | High Altitude Installations | 6 |
E. | 6 | |
F. | Combustible Materials Specification | 6 |
G. | Requirements for the |
|
| Commonwealth of Massachusetts | 7 |
User Guide
2 Operating Instructions
A. | Gas Fireplace Safety | 8 |
B. | Your Fireplace | 8 |
C. | Fan Kit (optional) | 9 |
D. | Clear Space | 9 |
E. | Decorative Doors and Fronts | 9 |
F. | Fixed Glass Assembly | 9 |
G. | Remote Controls, Wall Controls and Wall Switches 9 | |
H. | Before Lighting Fireplace | 9 |
I. | Lighting Instructions (IPI) | 10 |
J. | Lighting Instructions (Standing Pilot) | 11 |
K. | After Fireplace is Lit | 12 |
L. | Frequently Asked Questions | 12 |
3 Maintenance and Service |
| |
A. | Maintenance | 13 |
B. | Maintenance | 14 |
Installer Guide
4 Getting Started |
| |
A. | Typical Appliance System | 15 |
B. | Design and Installation Considerations | 16 |
C. Tools and Supplies Needed | 16 | |
D. Inspect Appliance and Components | 16 | |
5 Framing and Clearances |
| |
A. | Select Appliance Location | 17 |
B. | Construct the Appliance Chase | 18 |
C. | Clearances | 18 |
D. | Mantel and Wall Projections | 19 |
6 Termination Locations
A. Vent Termination Minimum Clearances | 20 |
7 Vent Information and Diagrams
A. | Approved Pipe | 22 |
B. | Vent Table Key | 22 |
C. | Use of Elbows | 22 |
D. | Measuring Standards | 22 |
E. | Vent Diagrams | 23 |
F. | Install Vertical Termination Baffle | 32 |
8 Vent Clearances and Framing
A. | Pipe Clearances to Combustibles | 33 |
B. | Wall Penetration Framing | 33 |
C. | Install the Ceiling Firestop | 34 |
D. | Install Attic Insulation Shield | 35 |
9 Appliance Preparation
A. | Convert from Top Vent to Rear Vent | 36 |
B. | Secure and Level the Appliance | 40 |
10 Install Vent Pipe
A. Assemble Pipe Sections (DVP Only) | 41 | |
B. | Assemble Vent Sections (SLP Only) | 42 |
C. Assemble Slip Sections | 42 | |
D. Secure the Vent Sections | 43 | |
E. | Disassemble Vent Sections | 43 |
F.Install Decorative Ceiling Components (SLP only) 44
G. | Install Metal Roof Flashing | 45 |
H. | Assemble and Install Storm Collar | 45 |
I. | Install | 46 |
J. | Install Vertical Termination Cap | 47 |
K. | Install Decorative Wall Components (SLP only) | 47 |
L. | Heat Shield Requirements for |
|
| Horizontal Termination | 47 |
M. | Install Horizontal Termination Cap | 48 |
11 Gas Information
A. | Fuel Conversion | 49 |
B. | Gas Pressure | 49 |
C. | Gas Connection | 49 |
D. | High Altitude Installations | 49 |
12 Electrical Information
A. | Wiring Requirements | 50 |
B. | Standing Pilot Ignition System Wiring | 50 |
C. | Intellifire Ignition System Wiring | 50 |
D. | Optional Accessories Requirements | 50 |
E. | Electrical Service and Repair | 51 |
F. | Junction Box Installation | 52 |
G. | Wall Switch Installation for Fan (Optional) | 52 |
13 Finishing
A. | Mantel and Wall Projections | 53 |
B. | Facing Material | 53 |
Heatilator • Caliber Mesh CD | 3 |
