Optional Wire Harness | Hearth and Home Technologies DV3732SBI

B. Vent Components Diagrams (continued)

13-5/8 IN.

346 mm

12-1/2 IN.

318 mm

20-3/4 IN.

527 mm

Optional Wire Harness

DESCRIPTION	PART NUMBER
10 ft. PV Wire Harness	PVI-WH10
20 ft. PV Wire Harness	PVI-WH20
40 ft. PV Wire Harness	PVI-WH40
60 ft. PV Wire Harness	PVI-WH60
80 ft. PV Wire Harness	PVI-WH80
100 ft. PV Wire Harness	PVI-WH100

Note: Wire harnesses required to power the PVI-SLP connect to the appliance and are ordered separately from PVI-SLP. Contact your dealer to order.

PVI-SLP

Power Vent Inline

16 IN.

406 mm

4-1/2 IN.

114 mm

9-3/16 IN.

(233 mm)

15IN.

(381 mm)

13-5/8 IN.

(346 mm)

16-11/16 IN.

424 mm

16-11/16 IN.

(424 mm)

12-1/2 IN.

(318 mm)

SLP-LPC

SLP Low Profile Cap

COAXIAL to COLINEAR VENTING

		LINK-DV30B	DVP-2SL	DV-46DVA-GCL
		Flex Liner Kit	Adapter	Coaxial/Colinear Appliance Connector
	Figure 16.11 Coaxial to Colinear Vent Components

74		Hearth & Home Technologies • DV3732SBI, DV3732SBIL • 2215-900 Rev. F • 9/12

Image 74

Hearth and Home Technologies DV3732SBI manual Optional Wire Harness, Pvi-Slp, Slp-Lpc, LINK-DV30B DVP-2SL DV-46DVA-GCL

Contents

HOT Surfaces ModelsWhat to do if you smell gas Congratulations Homeowner Reference Information Table of Contents User Guide Finishing Appliance SetupTroubleshooting Reference Materials Limited Lifetime Warranty Hearth & Home Technologies Inc Limited Lifetime Warranty Limited Lifetime Warranty Warranty Conditions Listing and Code Approvals Requirements for the Commonwealth of Massachusetts Your Fireplace Gas Fireplace SafetyOperating Instructions User Guide Fan Kit optional Fixed Glass AssemblyRemote Controls, Wall Controls and Wall Switches Decorative Doors and Fronts What to do if YOU Smell GAS Lighting Instructions IPIFinal inspection by GAS Valve After Fireplace is Lit Frequently Asked QuestionsIssue Solutions Maintenance and Service Logs Maintenance Tasks-Qualified Service TechnicianGasket Seal and Glass Assembly Inspection Firebox Getting Started Typical Appliance System Inspect Appliance and Components Design and Installation ConsiderationsTools and Supplies Needed Framing and Clearances Selecting Appliance Location Constructing the Appliance Chase Clearances Minimum FT. Maximum Mantel and Wall ProjectionsMinimum Minimum Unlimited Termination Locations Vent Termination Minimum Clearances Covered Alcove Applications Minimum Clearances for Termination Vent Table Key Vent Information and DiagramsApproved Pipe Use of Elbows Use of Flex Vent Vent Diagrams Top Vent Horizontal Termination One Elbow Fire Risk Installed Horizontally Top Vent Horizontal Termination Two Elbows Top Vent Horizontal Termination Three Elbows V1 Minimum H1 Maximum H1 + H2 Maximum Top Vent Vertical Termination No Elbows V1 = 60 ft. Max .3 m Exhaust restrictor Instructions Top Vent Vertical Termination Two Elbows Three Elbows Minimum Maximum Top Vent Vertical Termination Four 90º Elbows V1 MIN H1 MAX V2 MIN H2 MAX V3 MINPage Rear Vent Horizontal Termination Two Elbows MAX MIN + H 2 MAX Rear Vent Vertical Termination One Elbow Rear Vent Vertical Termination Three elbows MIN MAX + H 2 MAX Clearances to Combustibles Prior to installing the gas applianceCoaxial to Colinear Venting Termination Cap Flue Damper Rear Vent Connecting the DV-46DVA-GCL Adapter to Appliance Top VentConnecting the LINK-DV30B to the DV-46DVA-GCL adapter Wall Penetration Framing Vent Clearances and FramingPipe Clearances to Combustibles Combustible Wall Penetration Install the Ceiling Firestop Pipe DVP SLP Vaulted Ceiling Installation Install Attic Insulation ShieldFlat Ceiling Installation Appliance Preparation Top Vent Rear Vent Cut the metal retaining band and fold the sides out Securing and Leveling the Appliance 13 Proper Positioning, Leveling And Securing Assemble Vent Sections DVP Pipe Only Installing Vent Pipe DVP and SLP PipeAttach Vent to the Firebox Assembly Assemble Pipe Sections Assemble Vent Sections SLP Pipe Only Assemble Slip Sections Secure the Vent Sections Disassemble Vent Sections Install Decorative Ceiling Components SLP only Install Metal Roof Flashing Assemble and Install Storm Collar Heat Shield Requirements for Horizontal Termination Install Vertical Termination CapInstall Decorative Wall Components SLP only Install Horizontal Termination Cap DVP and SLP Pipe DVP-HPC1 DVP-HPC2 Gas Pressure Gas InformationFuel Conversion Gas Connection Electrical Information Wiring RequirementsOptional Accessories Requirements Code CSA C22.1 Intellifire Ignition Wiring Diagram with Remote Junction Box Installation Wall Switch Installation for Fan Optional Splatter Guard To install the Splatter GuardFinishing To Close the Lower Access Panel To Remove the Splatter Guard TOP View 16 Noncombustible Facing Diagram Facing Material Doors Template Elevated Hearth Systems Appliance Setup Install the Log Assembly Slot a Mate slot C with tab C Mate slot with locating screw Air Shutter Setting Install Louvers and TrimInstall Hood Air Shutter Settings Intellifire Ignition System TroubleshootingSymptom Possible Cause Corrective Action Ues to spark, and main Appliance Dimension Diagram Reference Materials Vent Components Diagrams DVP-AS2 DVP-TRAP DVP vent components DVP-TRAPFL RF6M RF12MBEK DVP-BEK2 COOL-ADD DVP-TV DVP-TB1 DVP-HRC-SS DVP-HRC-ZC-SS Horizontal Termination CAPSLP-HRC-SS SLP-HRC-ZC-SS Horizontal Termination CAP  B. Vent Components Diagrams SL-2DVP SLK-SNKD DVP-FBHT SLP-CCS-BK SLP-DCF-BKSLP-FLEX-TRAP SLP-TVHW SLP-LPC Optional Wire HarnessPVI-SLP LINK-DV30B DVP-2SL DV-46DVA-GCL Gas Fireplace DV Service Parts ListAt Depot #12 Valve Assembly Service Parts Contact Information