Valve Assembly | Heat & Glo LifeStyle 8000CFLP-OAKIPI manual

Service Parts	8000CF-OAK-IPI

Valve Assembly Diagram/ Parts List	Beginning Manufacturing Date: Jan. 2005
	Ending Manufacturing Date: ______

		1
Intermittent Pilot Ignition		2
Valve Assembly		2
		3
	4
	Note: Shutter
	sleeve not used	5
	on LP models	5
7	6
		10
		9
		8

	IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement				Stocked
	parts for your appliance please provide model number and serial number. All parts listed				Stocked
	in this manual may be ordered from an authorized dealer.				at Depot
	ITEM	DESCRIPTION	COMMENTS	PART NUMBER

		Pilot Assembly NG	Pre 002927628	4021-025	Y
	1	Pilot Assembly NG	Post 002927628	2090-012	Y
			Post 002927628	2090-012	Y
		Pilot Assembly LP	Pre 002927628	4021-026	Y
			Pre 002927628	4021-026	Y
			Post 002927628	2090-013	Y
			Post 002927628	2090-013	Y
	2	18” Flexible Gas Connector		530-302A	Y
	3	Burner Oriﬁce NG (#31C)		582-831	Y
	3	Burner Oriﬁce LP (1.8mm)		582-818	Y
		Burner Oriﬁce LP (1.8mm)		582-818	Y
	4	Shutter Sleeve (NG)		2026-130	Y
	5	Shutter Bracket Assembly		2026-017	Y
	6	Valve Bracket		2059-104
	7	Flex Ball Valve Assembly		302-320A	Y
	8	Valve NG		750-500	Y
	8	Valve LP		750-501	Y
		Valve LP		750-501	Y
	9	Module		593-592	Y
	10	Wire Assembly		593-590A	Y
		3 Volt Transformer		593-593A	Y
		2” Jumper Wire		2012-206	Y
		Wire Assembly		2045-024	Y

60	Heat & Glo • 8000CF-OAK-IPI • 2059-900 Rev. R • 6/09

Image 60

Heat & Glo LifeStyle 8000CFLP-OAKIPI, 8000CF-OAK-IPI owner manual Valve Assembly

Contents

What to do if you smell gas HOT SurfacesHot glass will cause burns Congratulations Homeowner Reference InformationXxxxxxxx Table of Contents User Guide Appliance Setup TroubleshootingFinishing Reference Materials Limited Lifetime Warranty Limited Lifetime Warranty Listing and Code Approvals Installation of Carbon Monoxide Detectors Requirements for the Commonwealth of Massachusetts Gas Fireplace Safety Operating Instructions User GuideYour Fireplace Fixed Glass Assembly Remote Controls, Wall Controls and Wall SwitchesFan Kit optional Clear Space Lighting Instructions IPI Final inspection byWhat to do if YOU Smell GAS GAS Valve Frequently Asked Questions Issue SolutionsAfter Fireplace is Lit Maintenance and Service Maintenance Tasks-HomeownerGlass Cleaning Remote Control Maintenance Tasks-Qualiﬁed Service Technician Gasket Seal and Glass Assembly InspectionVenting Logs Either cobrahead or SIT Getting Started Typical Appliance System Design and Installation Considerations Tools and Supplies NeededInspect Appliance and Components Any such action may cause a ﬁre hazard Framing and Clearances Selecting Appliance Location Minimum Framing Dimensions Constructing the Appliance ChaseClearances Mantel and Wall Projections Combustible MantelsCombustible Mantel Legs or Wall Projections Termination Locations Vent Termination Minimum Clearances = Area Where Terminal is not Permitted = Vent Terminal = AIR Supply Inlet Vent Information and Diagrams Approved PipeVent Table Key Use of Elbows Vent Diagrams Top Vent Horizontal Termination One Elbow Two ElbowsV1 Minimum H1 Maximum V1 Minimum H1 + H2 Maximum Top Vent Horizontal Termination Three Elbows V1 Min H1 Max V2 Min H2 Max V1 + V2 Min H1 + H2 Max Chart Vertical Top Vent Top Vent Vertical Termination Two Elbows H1 Maximum V1 + MinimumH1+ H2 V1+ V2 Minimum H1+ H2 Maximum Vent Clearances and Framing Pipe Clearances to CombustiblesHeat Shield Above First 900 Elbow Required Wall Penetration Framing Combustible Wall PenetrationNon-Combustible Wall Penetration Install the Ceiling Firestop Pipe DVP Install Attic Insulation Shield Flat Ceiling InstallationVaulted Ceiling Installation Temporary Access Panel Appliance PreparationAttaching Sheetrock Ledges Installing the Fiberglass Gasket Securing and Leveling the Appliance Completing Grate Set-up Checking Pilot Plate Installing Vent Pipe Attach Vent to the Firebox AssemblyAssemble Vent Sections Assemble Pipe Sections Assemble Slip Sections Secure the Vent Sections Rotate Seams for Disassembly Disassemble Vent Sections Install Metal Roof Flashing Assemble and Install Storm Collar Install Vertical Termination Cap Heat Shield Requirements for Horizontal Termination Install Horizontal Termination Cap Ansi Z223.1 and CAN/CGA-B149 installation codes Gas Information Fuel ConversionGas Pressure Gas Connection Wiring Requirements Intelliﬁre Ignition System WiringOptional Accessories Requirements Electrical Information Electrical Service and Repair Intelliﬁre Pilot Ignition IPI Wiring Diagram Junction Box Installation Wall Switch Installation for Fan Optional Finishing Facing Material Appliance Setup Install the Optional Refractory Ember Placement Log Assembly LOGS-8OAK Install the Log Assembly Heat & Glo 8000CF-OAK-IPI 2059-900 Rev. R 6/09 Install the Mesh Install Trim and/or SurroundAir Shutter Setting Air Shutter Settings Troubleshooting Symptom Possible Cause Corrective ActionIntelliﬁre Ignition System Ues to spark, and main Appliance Dimension Diagram Reference MaterialsLocation Inches Millimeters Vent Components Diagrams DVP vent components DVP-TRAP Horizontal Termination Cap RF6M RF12M BEK DVP-BEK2DVP-TRAPFL COOL-ADD DVP-TB1 305 mm Log Set Assembly Service Parts Service Parts List StockedAt Depot Valve Assembly Contact Information