Reference Materials | Heat & Glo LifeStyle 8000CF-OAK-IPI specs

16 Reference Materials

A. Appliance Dimension Diagram

Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 5.

A

		B
		C
		D
		E
		ELECTRICAL
	GAS LINE	ACCESS
	GAS LINE	K
	ACCESS	K
	ACCESS

S

F			J		P
F			J		O
	H				O
	H	I			Q
		I

					N
G				L	R
G				L

M

Location	Inches	Millimeters		Location	Inches	Millimeters
A	35-1/2	901		J	23-1/2	598
B	17-3/4	450		K	39-1/4	996
C	21-1/2	548		L	43	1091
D	13	328		M	48	1221
E	8	203		N	7	177
F	40	1015		O	34-1/4	870
G	9-1/8	233		P	46-3/4	1186
H	2-1/4	56		Q	2-1/4	58
I	4-1/8	104		R	5-1/4	134
				S	56-1/2	1433

Figure 16.1 Appliance Dimensions

Heat & Glo • 8000CF-OAK-IPI • 2059-900 Rev. R • 6/09

53

Image 53

Heat & Glo LifeStyle 8000CF-OAK-IPI Reference Materials, Appliance Dimension Diagram, Location Inches Millimeters

Contents

Hot glass will cause burns What to do if you smell gasHOT Surfaces Xxxxxxxx CongratulationsHomeowner Reference Information User Guide Table of Contents Troubleshooting Appliance SetupFinishing Reference Materials Limited Lifetime Warranty Limited Lifetime Warranty Listing and Code Approvals Requirements for the Commonwealth of Massachusetts Installation of Carbon Monoxide Detectors Your Fireplace Gas Fireplace SafetyOperating Instructions User Guide Remote Controls, Wall Controls and Wall Switches Fixed Glass AssemblyFan Kit optional Clear Space Final inspection by Lighting Instructions IPIWhat to do if YOU Smell GAS GAS Valve After Fireplace is Lit Frequently Asked QuestionsIssue Solutions Maintenance Tasks-Homeowner Maintenance and ServiceGlass Cleaning Remote Control Gasket Seal and Glass Assembly Inspection Maintenance Tasks-Qualiﬁed Service TechnicianVenting Logs Either cobrahead or SIT Typical Appliance System Getting Started Tools and Supplies Needed Design and Installation ConsiderationsInspect Appliance and Components Any such action may cause a ﬁre hazard Selecting Appliance Location Framing and Clearances Clearances Minimum Framing DimensionsConstructing the Appliance Chase Combustible Mantel Legs or Wall Projections Mantel and Wall ProjectionsCombustible Mantels Vent Termination Minimum Clearances Termination Locations = Vent Terminal = AIR Supply Inlet = Area Where Terminal is not Permitted Approved Pipe Vent Information and DiagramsVent Table Key Use of Elbows Two Elbows Vent Diagrams Top Vent Horizontal Termination One ElbowV1 Minimum H1 Maximum V1 Minimum H1 + H2 Maximum V1 Min H1 Max V2 Min H2 Max V1 + V2 Min H1 + H2 Max Top Vent Horizontal Termination Three Elbows Vertical Top Vent Chart H1+ H2 V1+ V2 Minimum H1+ H2 Maximum Top Vent Vertical Termination Two ElbowsH1 Maximum V1 + Minimum Pipe Clearances to Combustibles Vent Clearances and FramingHeat Shield Above First 900 Elbow Required Non-Combustible Wall Penetration Wall Penetration FramingCombustible Wall Penetration Pipe DVP Install the Ceiling Firestop Vaulted Ceiling Installation Install Attic Insulation ShieldFlat Ceiling Installation Attaching Sheetrock Ledges Temporary Access PanelAppliance Preparation Securing and Leveling the Appliance Installing the Fiberglass Gasket Checking Pilot Plate Completing Grate Set-up Attach Vent to the Firebox Assembly Installing Vent PipeAssemble Vent Sections Assemble Pipe Sections Secure the Vent Sections Assemble Slip Sections Disassemble Vent Sections Rotate Seams for Disassembly Assemble and Install Storm Collar Install Metal Roof Flashing Heat Shield Requirements for Horizontal Termination Install Vertical Termination Cap Ansi Z223.1 and CAN/CGA-B149 installation codes Install Horizontal Termination Cap Fuel Conversion Gas InformationGas Pressure Gas Connection Intelliﬁre Ignition System Wiring Wiring RequirementsOptional Accessories Requirements Electrical Information Intelliﬁre Pilot Ignition IPI Wiring Diagram Electrical Service and Repair Wall Switch Installation for Fan Optional Junction Box Installation Facing Material Finishing Appliance Setup Ember Placement Install the Optional Refractory Install the Log Assembly Log Assembly LOGS-8OAK Heat & Glo 8000CF-OAK-IPI 2059-900 Rev. R 6/09 Install Trim and/or Surround Install the MeshAir Shutter Setting Air Shutter Settings Intelliﬁre Ignition System TroubleshootingSymptom Possible Cause Corrective Action Ues to spark, and main Location Inches Millimeters Appliance Dimension DiagramReference Materials DVP vent components Vent Components Diagrams Horizontal Termination Cap DVP-TRAP BEK DVP-BEK2 RF6M RF12MDVP-TRAPFL COOL-ADD 305 mm DVP-TB1 Service Parts Log Set Assembly At Depot Service Parts ListStocked Valve Assembly Contact Information