Mantel and Wall Projections | Heat & Glo LifeStyle 8000CFLP-OAKIPI

D. Mantel and Wall Projections

WARNING! Risk of Fire! Comply with all minimum clear- ances as speciﬁed. Framing or ﬁnishing material closer than the minimums listed must be constructed entirely of noncom- bustible materials (i.e., steel studs, concrete board, etc).

Combustible Mantels

		18
Note: All		14-1/4
measurements		10-1/2
in inches.		10-1/2
in inches.		6-3/4
		6-3/4
		3
		12-1/4
		11-1/8
		10
		8-7/8
		7-3/4
		MEASUREMENTS FROM
		TOP EDGE OF HOOD
Figure 5.3	Minimum Vertical and Maximum Horizontal
	Dimensions of Combustibles

Combustible Mantel Legs or Wall Projections

	1 in.
TOP VIEW	MIN.
TOP VIEW

3 in.

MIN. 3 ft. MAX.

Figure 5.4 Combustible Mantel Leg or Wall Projections (Acceptable on both sides of opening)

20	Heat & Glo • 8000CF-OAK-IPI • 2059-900 Rev. R • 6/09

Image 20

Heat & Glo LifeStyle 8000CFLP-OAKIPI, 8000CF-OAK-IPI owner manual Mantel and Wall Projections, Combustible Mantels

Contents

Hot glass will cause burns What to do if you smell gasHOT Surfaces Xxxxxxxx CongratulationsHomeowner Reference Information Table of Contents User Guide Appliance Setup TroubleshootingFinishing Reference Materials Limited Lifetime Warranty Limited Lifetime Warranty Listing and Code Approvals Installation of Carbon Monoxide Detectors Requirements for the Commonwealth of Massachusetts Your Fireplace Gas Fireplace SafetyOperating Instructions User Guide Fixed Glass Assembly Remote Controls, Wall Controls and Wall SwitchesFan Kit optional Clear Space Lighting Instructions IPI Final inspection byWhat to do if YOU Smell GAS GAS Valve After Fireplace is Lit Frequently Asked QuestionsIssue Solutions Maintenance and Service Maintenance Tasks-HomeownerGlass Cleaning Remote Control Maintenance Tasks-Qualiﬁed Service Technician Gasket Seal and Glass Assembly InspectionVenting Logs Either cobrahead or SIT Getting Started Typical Appliance System Design and Installation Considerations Tools and Supplies NeededInspect Appliance and Components Any such action may cause a ﬁre hazard Framing and Clearances Selecting Appliance Location Clearances Minimum Framing DimensionsConstructing the Appliance Chase Combustible Mantel Legs or Wall Projections Mantel and Wall ProjectionsCombustible Mantels Termination Locations Vent Termination Minimum Clearances = Area Where Terminal is not Permitted = Vent Terminal = AIR Supply Inlet Vent Information and Diagrams Approved PipeVent Table Key Use of Elbows Vent Diagrams Top Vent Horizontal Termination One Elbow Two ElbowsV1 Minimum H1 Maximum V1 Minimum H1 + H2 Maximum Top Vent Horizontal Termination Three Elbows V1 Min H1 Max V2 Min H2 Max V1 + V2 Min H1 + H2 Max Chart Vertical Top Vent H1+ H2 V1+ V2 Minimum H1+ H2 Maximum Top Vent Vertical Termination Two ElbowsH1 Maximum V1 + Minimum Vent Clearances and Framing Pipe Clearances to CombustiblesHeat Shield Above First 900 Elbow Required Non-Combustible Wall Penetration Wall Penetration FramingCombustible Wall Penetration Install the Ceiling Firestop Pipe DVP Vaulted Ceiling Installation Install Attic Insulation ShieldFlat Ceiling Installation Attaching Sheetrock Ledges Temporary Access PanelAppliance Preparation Installing the Fiberglass Gasket Securing and Leveling the Appliance Completing Grate Set-up Checking Pilot Plate Installing Vent Pipe Attach Vent to the Firebox AssemblyAssemble Vent Sections Assemble Pipe Sections Assemble Slip Sections Secure the Vent Sections Rotate Seams for Disassembly Disassemble Vent Sections Install Metal Roof Flashing Assemble and Install Storm Collar Install Vertical Termination Cap Heat Shield Requirements for Horizontal Termination Install Horizontal Termination Cap Ansi Z223.1 and CAN/CGA-B149 installation codes Gas Information Fuel ConversionGas Pressure Gas Connection Wiring Requirements Intelliﬁre Ignition System WiringOptional Accessories Requirements Electrical Information Electrical Service and Repair Intelliﬁre Pilot Ignition IPI Wiring Diagram Junction Box Installation Wall Switch Installation for Fan Optional Finishing Facing Material Appliance Setup Install the Optional Refractory Ember Placement Log Assembly LOGS-8OAK Install the Log Assembly Heat & Glo 8000CF-OAK-IPI 2059-900 Rev. R 6/09 Install the Mesh Install Trim and/or SurroundAir Shutter Setting Air Shutter Settings Intelliﬁre Ignition System TroubleshootingSymptom Possible Cause Corrective Action Ues to spark, and main Location Inches Millimeters Appliance Dimension DiagramReference Materials Vent Components Diagrams DVP vent components DVP-TRAP Horizontal Termination Cap RF6M RF12M BEK DVP-BEK2DVP-TRAPFL COOL-ADD DVP-TB1 305 mm Log Set Assembly Service Parts At Depot Service Parts ListStocked Valve Assembly Contact Information