|
| (GREEN) |
|
|
|
|
|
|
|
|
|
|
|
|
|
| JUNCTION BOX |
|
|
| |
| (WHITE) |
|
|
|
|
|
|
|
|
|
| (BLACK) |
|
|
|
|
|
|
|
|
|
| (BROWN) | (BROWN) |
|
|
|
|
|
|
|
|
(WHITE) | (RED) | (BROWN) |
|
|
|
|
|
|
|
|
(BLACK) |
|
|
|
|
|
|
|
|
|
|
(BROWN) |
|
|
|
|
|
|
|
|
|
|
(RED) |
|
|
|
|
|
|
| WHITE (HTL) |
| |
| (GREEN) |
|
|
|
|
|
|
| ||
(ORANGE) |
|
|
|
|
|
| YELLOW (H&G) |
| ||
|
|
|
|
|
| RED |
| |||
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| |
| GROUND |
|
|
|
|
| GREEN |
|
|
|
IPI | BLACK |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| ||
VALVE |
|
|
|
|
|
|
|
|
| REAR VIEW |
|
| IPI PILOT | G | Y | R |
|
|
| ||
| IPI |
| (BROWN) |
| R Y G |
| ||||
|
|
|
|
|
|
| ||||
| MODULE | (BROWN) |
|
|
|
|
|
|
| |
|
| (RED) | (RED) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
| (BLACK) | (BLACK) |
|
|
|
|
|
|
|
|
| 3V DC |
|
|
|
|
|
|
| |
FLAME |
|
|
|
|
|
|
|
|
|
|
SOLENOID |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| FRONT VIEW |
|
| (RED) |
|
|
|
|
|
|
|
|
| FLAME ON | (RED) |
|
|
|
|
|
|
|
|
|
| (ORANGE) |
|
|
| (YELLOW) |
|
| ||
| FLAME HIGH/LOW | (ORANGE) |
|
|
| FACTORY | ||||
(BLACK) |
|
|
|
|
| |||||
|
| (BLACK) |
|
|
|
|
| CONNECTED | ||
(WHITE) |
|
|
|
|
|
|
| TOGETHER | ||
| FAN |
|
|
|
| (YELLOW) |
| |||
|
|
|
|
|
|
|
| |||
(GROUND) |
|
|
|
|
|
|
|
|
| |
CONNECTION |
|
|
|
| FAN THEMOSTAT |
|
| |||
| (BLACK) |
|
|
|
| |||||
TO HEAT ZONE |
|
|
|
|
|
|
| |||
|
|
| AC |
|
|
| (BLACK) |
|
|
|
|
|
| PLUG |
|
|
| AUX |
|
| |
|
|
|
|
|
|
|
| |||
|
|
| GROUND PIGTAIL |
| CONNECTION | |||||
NOTE 1: BROWN AND RED WIRES FROM |
|
| ||||||||
| GREEN |
|
|
|
|
|
|
NOTE 2: BLACK, WHITE AND GREEN WIRES
RUN
NOTE 3: GREEN WIRE FROM
TIE INTO GROUND A THE JUNCTION BOX
WHERE 110V SERVICE IS REQUIRED.
Figure 12.2 IPI Wiring diagram for optional
FIREBOX
BACK
LIGHT 1
BACK
LIGHT 2
D. Electrical Service and Repair
WARNING! Risk of Shock! Label all wires prior to dis- connection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.
WARNING! Risk of Shock! Replace damaged wire with type 105° C rated wire. Wire must have high temperature insulation.
E. Junction Box Installation
If the box is being wired from the INSIDE of the appli- ance:
•Remove the screw attaching the junction box/receptacle to the outer shell, rotate the junction box inward to dis- engage it from the outer shell (see Figure 12.4).
•Pull the electrical wires from outside the appliance through the opening into the valve compartment and secure wires with a Romex connector. See Figure 12.4.
•Make all necessary wire connections to the junction box/receptacle and reattach the junction box/receptacle to the outer shell.
Heat & Glo • | 43 |