TOP View

1/2 in. Min.

FIREPLACE

OPENING

2-3/4 in. Min.

1 in.		Unlimited



Max.

3-1/4 in. Min.

Note: Clearance from opening to perpendicular wall.

Figure 5.9 Combustible Mantel Leg or Wall Projections (Acceptable on both sides of opening)

SHEETROCK

3.5 in.

= AIR SPACE REQUIRED

Figure 5.10 Non-Combustible Zone (PIER and ST)

SHEETROCK

3.5 in.

= AIR SPACE REQUIRED

Figure 5.11 Non-Combustible Zone (LCOR and RCOR)

22	Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. H • 8/11

Page 22

Image 22

Heat & Glo LifeStyle ST-36TRB-IPI owner manual TOP View

Contents

HOT Surfaces What to do if you smell gasHot glass will cause burns Congratulations Homeowner Reference Information Table of Contents User Guide Finishing Appliance SetupTroubleshooting Reference Materials  B. Limited Lifetime Warranty Limited Lifetime Warranty Warranty Conditions Listing and Code Approvals Installation of Carbon Monoxide Detectors Requirements for the Commonwealth of Massachusetts Operating Instructions User Guide Gas Fireplace SafetyYour Fireplace Remote Controls, Wall Controls and Wall Switches Blower InstallationFixed Glass Assembly Blower Kit optional What to do if YOU Smell GAS Lighting Instructions IPIFinal inspection by GAS Valve Issue Solutions Frequently Asked QuestionsAfter Fireplace is Lit Glass Cleaning Maintenance and ServiceMaintenance Tasks-Homeowner Remote Control Venting Maintenance Tasks-Qualiﬁed Service TechnicianGasket Seal and Glass Assembly Inspection Logs Burner Ignition and Operation IPI Pilot Flame Patterns Getting Started Typical Appliance System Inspect Appliance and Components Design and Installation ConsiderationsTools and Supplies Needed Any such action may cause a ﬁre hazard Framing and Clearances Selecting Appliance Location Constructing the Appliance Chase Clearances RCOR-36TRB-IPI See-Through Non-Combustible Mantel Mantel and Wall Projections See-Through Combustible MantelPIER/LCOR/RCOR Combustible Mantel PIER/LCOR/RCOR Non-Combustible Mantel TOP View Vent Termination Minimum Clearances Termination LocationsGas, Wood or Fuel Oil Termination Cap Covered Alcove Applications Vent Table Key Vent Information and DiagramsApproved Pipe Use of Elbows Top Vent-Horizontal Termination-Two 45 Elbows Vent DiagramsTo SLP series vent pipe, if desired Elbow on rear vent appliances V1 Minimum H1 Maximum Top Vent Horizontal Termination One ElbowTwo Elbows V1 Minimum H1 + H2 Maximum 152 mm Top Vent Horizontal Termination Three Elbows305 mm Exhaust restrictor Instructions Break Here 15 ft 20 ft 25 ft 30 ft 35 ft 40 ft 45 ft 50 ft 55 ft 12 ft 18 ft V1 + V2 + H1 = 50 ft 15.2 m Maximum Two Elbows Three ElbowsMaximum + V 2 Minimum H1+ H2 V1 + V2 Minimum H1+ H2 MaximumPage H1 Maximum V1 Minimum H2 Maximum H1+ H2 Maximum Rear Vent Horizontal Termination Two ElbowsH1 Maximum V1 Minimum H2+ H3 H1+ H2+ H3 V1+ H1 = 40 ft 12.2 m Maximum Rear Vent Vertical Termination One ElbowV1 Minimum H1 Maximum Minimum + H 2 Maximum H1 Maximum V1 Minimum H1+ H2 Maximum Rear Vent Vertical Termination Three ElbowsV1 Minimum H1+ H2+ H3 Maximum Pipe Clearances to Combustibles Vent Clearances and FramingContinue Adding Vent Components Non-Combustible Wall Penetration Wall Penetration FramingCombustible Wall Penetration Correct Vertical Penetration Framing Pipe DVP SLP Flat Ceiling Installation Install Attic Insulation ShieldVaulted Ceiling Installation Top Vent Appliance PreparationProceed to . C Rear Vent Cut the metal retaining band Securing and Leveling the Appliance Attach Nailing Tab to Front Corner of Unit Assemble Vent Sections DVP Pipe Only Installing Vent Pipe DVP and SLP PipeAttach Vent to the Firebox Assembly Assemble Pipe Sections DVP Pipe Only Assemble Vent Sections SLP Pipe Only Assemble Slip Sections Secure the Vent Sections Disassemble Vent Sections Install Decorative Ceiling Components SLP only Install Metal Roof Flashing Assemble and Install Storm Collar Heat Shield Requirements for Horizontal Termination Install Vertical Termination CapInstall Decorative Wall Components SLP only Important Notice Heat shields may not be ﬁeld constructed Install Horizontal Termination Cap DVP and SLP Pipe DVP-HPC1 DVP-HPC2 Gas Pressure Gas InformationFuel Conversion Gas Connection Optional Accessories Requirements Wiring RequirementsElectrical Information Intelliﬁre Ignition Wiring Diagram with Remote Receiver Junction Box Installation Wall Switch Installation for Fan Optional Finishing To install the Splatter GuardSplatter Guard To Close the Lower Access Panel To Remove the Splatter Guard Mantel and Wall Projections See-Through Mantel Projection PIER/LCOR/RCOR Mantel Projection Finishing Material Facing MaterialStop ﬁnishing material ﬂush with opening Finishing materials over 1 inch thick Finishing material between 1 and 2 inches thick Elevated Hearth Systems Appliance Setup Install the Log Assembly 2128-935 Indentations Air Shutter Setting Install Trim Kits and SurroundsAir Shutter Settings Symptom Possible Cause Corrective Action TroubleshootingIntelliﬁre Ignition System ﬂame rectiﬁcation has Reference Materials Appliance Dimension DiagramLocation Inches Millimeters Electrical Access GAS Line Left View Front View Right View Pier Dimensions 24-1/2 Left View Front View Electrical Access GAS Line Right View40-1/2 33-1/2 Vent Components Diagrams DVP-AS2 DVP-TRAP Horizontal Termination Cap DVP-TRAPFL RF6M RF12MBEK DVP-BEK2 COOL-ADD DVP-TV PVI-SLP Optional Wire HarnessPower Vent Inline SLP-LPC Support ElbowCeiling Firestop SLP-WS DVP-FBHT SLP-SNKD SLP-CCS-BKSLP-DCF-BK At Depot Service PartsLog Set Assembly See Through Direct Vent Gas Fireplace PIER-36TRB-IPI Pier Direct Vent Fireplace LCOR-36TRB-IPI Left Corner Direct Vent Fireplace RCOR-36TRB-IPI Right Corner Direct Vent Fireplace #15 Valve Assembly Stocked Service Parts List LPK-DXV Contact Information