[Example: Connecting Antenna
through STB and VCR]

CONNECTION

Terminal Positions

SD MEMORY

CARD h

PUSH-EJECT

 

P

 

 

 

 

 

 

 

 

 

P

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

w

 

 

 

OK

 

 

 

 

 

 

INPUT(RGB)

 

 

 

 

 

 

 

ANT

 

AUDIO

 

 

 

 

 

 

 

 

 

 

 

ertyu

 

 

ANALOG RGB

a

 

 

 

 

 

 

 

 

PC

 

 

 

 

 

 

 

 

 

INPUT(HDMI)

 

 

INPUT INPUT INPUT INPUT

OUTPUT

 

 

AUDIO

 

 

(AV1)

(AV2)

(AV3)

(AV4)

WOW, SRS and

symbol are trademarks of SRS Labs, Inc.

 

 

 

Y/VIDEO

Y/VIDEO

 

 

 

 

 

 

 

 

 

 

 

 

 

Licensed by BBE Sound, Inc. under USP5510752 and 5736897.

 

 

 

 

 

 

 

 

BBE and BBE symbol are registered trademarks of BBE Sound, Inc.

 

 

 

 

 

 

 

SUB

 

i

HDMI2

s

 

P

P

 

 

WOOFER

 

 

P

P

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

HDMI1

 

PH35814

AUDIO

AUDIO

AUDIO

AUDIO

AUDIO

SERVICE USE ONLY

 

 

 

L

L

L

L

L

 

 

o

 

 

C

C

C

C

 

 

 

 

 

 

R

R

R

R

R

 

 

 

 

 

 

 

 

 

 

POWER SWIVEL

 

 

 

A C

 

 

 

 

 

 

 

q

Connecting Procedure

PH35826

 

 

S-VIDEO

INPUT(AV5)

L/MONO

AUDIO VIDEO

 

R

 

Rear

qPower Cord Socket

g w Aerial Socket

e AV1

fr AV2 t AV3 y AV4

u Monitor Out and Sub Woofer i Service use only

oPower Swivel Terminal

d(see 36 )

aPC Connection terminals (D-sub 15 pin and mini stereo for Audio)

sHDMI1, 2 and mini stereo for Audio

Side

dAV5

fHeadphone input

gPhoto Input terminal

hSD Memory Card slot

This unit is ready for various kinds of connections. Make a connection in the following steps. Be sure to turn off the Main Power fi rst when connecting external equipments.

1.Connect Power Cord to the rear panel.

2.Connect Aerial Lead.

3.Connect your external equipments to the unit if any.

4.Connect the Power Plug to the Wall Socket.

1. Connecting Power Cord to the Rear Panel

Connect Power Cord to the monitor.

*Make sure not to connect the Power Plug to the Wall Socket until all connections are completed.

2. Connecting Aerial Lead.

There are two ways to connect Aerial Lead.

qWhen you do not have any other external equipment:

Connect the Aerial Lead directly into the Socket at rear panel.

wWhen you have one or more external devices to connect:

STB VCR

IN

IN

OUT

OUT

1. Use RF cable to connect between each equipment and Antenna.

2.Connect the Aerial Lead to an equipment‘In’Socket marked

3.Connect the RF cable from the equipment ‘Out’ to the other equipment ‘In.’

4. Then, connect from the equipment ‘Out’ to “ANT” on the plasma screen Socket on marked .

Precautions when connecting the aerial

Please use a coaxial cable which is free from interference to connect the aerial. Avoid using a parallel fl at feeder wire as interference may occur, causing reception to be unstable and stripe noise to appear on the screen.

Avoid using indoor aerial as this may be affected by interference. Please use CATV net or outdoor aerial.

For safety, install an external aerial conforming to AS1417.1 (applicable for Australia only)

If there are noise appearance in the picture of VHF-Low band channel, please use the double-shielded cable (not provided) for RF LEADS to reduce the noise.

13

Page 14
Image 14
Hitachi 42PD8800TA user manual Connection, Terminal Positions, Connecting Procedure