English
SPECIFICATIONS
Type of power | Piston reciprocating |
Air pressure (Gauge) | 4.9 – 8.3 bar (70 – 120 psi.) |
Applicable staples | ref. Fig. |
Amount of loadable staples | 150 staples |
Size | 365 mm (L) ⋅ 254 mm (H) ⋅ 76 mm (W) |
Weight | 2.0 kg (4.4 lbs) |
Hose (inside diam.) | 6 mm (1/4”) |
STAPLE SELECTION
Choose a suitable staple from Fig. Staples which are not shown in Fig. can not be driven with this tool.
|
|
|
|
| 16 Gauge 7/16" Crown | |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Min. |
|
|
|
|
|
| Max. | ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 1.61mm | (.063") |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| (1") |
|
|
|
|
|
|
| 50mm(2") |
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
| 25mm |
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
| 7.9mm |
|
|
| 1.45mm |
| ||||||||||
|
|
|
|
|
|
|
|
| ||||||||
|
|
| (.057") |
|
|
|
|
|
| |||||||
| (.309") |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Dimension of staples |
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
STANDARD ACCESSORIES |
|
|
|
| ||||||||||||
(1) |
| Hexagon bar wrench for M5 screw ........................... | 1 | |||||||||||||
(2) |
| Eye protection | ............................................................. |
|
|
|
| 1 | ||||||||
(3) |
| Oiler ............................................................................. |
|
|
|
|
|
|
|
|
|
| 1 | |||
OPTIONAL ACCESSORY
Sequential Trip Mechanism Kit (Code No.876762) (Sequential Fire Parts Set, Single Shot Parts)
With the sequential fire parts, the staple is driven only by squeezing the trigger after pushing down the push lever.
By installing these parts, driving staples into improper positions and unexpected firing of staples caused by accidental operation of the push lever can be prevented.
APPLICATIONS
Construction work such as wall sheathing, roof decking, subflooring.
Mobile and modular home construction.
Making wooden boxes, palletes, and drums.
PREPARATION PRIOR TO OPERATION
1. Prepare the hose
Be sure to use the hose provided with minimum 6 mm (1/4”) inside diameter.
NOTE:
The air supply hoses must have a minimum working pressure rating of 12.8 bar (180 psi) or 150 percent of the maximum pressure produced in the air supply system, whichever is higher.
2.Check on safety
CAUTIONS:
Unauthorized persons (including children) must be kept away from the equipment.
Wear eye protection.
Check the retaining screws which fix the exhaust cover, etc. for tightness.
Check the stapler for air leaks and defective or rusty parts.
Check whether or not the push lever works correctly. Also check whether or not any dirt has adhered to the moving parts of the push lever.
Recheck on operational safety.
BEFORE USE
1.Check the air pressure
CAUTION:
The air pressure must be constantly maintained at 4.9
–8.3 bar (70 – 120 psi.).
Adjust the air pressure between 4.9 to 8.3 bar (70 – 120 psi.) according to the diameters and length of staples and hardness of the wood being stapled. Pay special attention to the output pressure, capacity, and piping on the air compressor, so that air pressure does not exceed the specified limit. Note that excessive pressure may affect overall performance, service life, and safety.
2. Lubrication
(1)Prior to operating this stapler, be sure to provide an air set between the air compressor and this device. Lubrication through the air set offers smooth operation, extended service life, and anticorrosion.
Adjust the oiler so that a single drop of oil is supplied at intervals of 5 to 10 stapling cycles.
7