TROUBLESHOOTING
Symptoms That Seemingly Appear to be Failures
■Make the checks suggested below depending on the symptoms observed. If the symptoms remain uncorrected, contact your dealer.
WARNING • Customer servicing can be hazardous.
Symptom | Point to check | See | |||||||
page | |||||||||
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| |||
• No picture with the power- |
|
|
|
| • Check the way the power cable is connected. | 6 | |||
|
|
|
| ||||||
indicating lamp off. |
|
|
|
| • Press the power switch. | 7 | |||
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| 9 | |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| |
• The message “POWER |
|
|
|
|
|
| No sync signal is detected. | 6 | |
|
|
|
|
|
| ||||
SAVE” is displayed. |
|
|
|
|
|
| • Check the way the signal cable is connected. | ||
|
|
|
|
|
|
| |||
|
|
| POWER SAVE | • Make sure that the switch of the computer, | 7 | ||||
• No picture with the power |
|
|
|
|
|
| imaging equipment , etc., is turned on. | 9 | |
|
|
|
|
|
| • Make sure the computer is not in the | |||
indicating lamp flickering in |
|
|
|
|
|
|
| ||
|
|
|
|
|
| mode. | 21 | ||
green. |
|
|
|
|
|
| |||
|
|
|
|
|
| • Check to see if the input selection matches the | 22 | ||
|
|
|
|
|
|
| connection terminal. | ||
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| |
• The message “OUT OF |
|
|
|
|
|
| An input signal is not received normally. | 6 | |
|
|
|
|
|
| ||||
FREQUENCY” is displayed. |
|
|
|
|
|
| • Check to see if the input signal matches the | 7 | |
|
|
| OUT OF FRQUENCY | monitor specifications. | |||||
|
|
| • Check the way the signal cable is connected. | 21 | |||||
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
| 27 | |
|
|
|
|
|
|
|
| 29 | |
|
|
|
|
|
|
|
|
| |
• The power indicating lamp is |
|
|
|
|
|
| • Check the contrast and brightness settings | 6 | |
normally lit but no picture . |
|
|
|
|
|
| (adjust them for higher contrast and brightness). | 7 | |
|
|
|
|
|
|
| • Check the way the signal cable is connected. | ||
|
|
|
|
|
|
|
| 11 | |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| 13 | |
|
|
|
|
|
|
|
|
| |
• The display image appears |
|
|
|
|
|
| • Adjust the dot clock frequency and phase. | 16 | |
|
|
|
|
|
| ||||
flowing slantwise. |
|
|
|
|
|
| (Adjust the dot clock frequency first, the dot clock | ||
|
|
|
|
|
| 25 | |||
• Text displayed across the |
|
|
|
|
|
| phase next.) | ||
screen appears vertically |
|
|
|
|
|
| (RGB input) |
| |
|
|
|
|
|
|
| |||
streaked, with the characters |
|
|
|
|
|
|
| ||
in vertical columns blurred. |
|
|
|
|
|
|
| ||
|
|
| |||||||
• Text displayed across the | • Adjust the dot clock phase for the clearest | 16 | |||||||
screen appears blurred. | viewing. | ||||||||
26 | |||||||||
• A fine pattern flickers when | (RGB input) | ||||||||
|
| ||||||||
displayed on the screen. |
|
| |||||||
|
|
| |||||||
• The remote controller does not work. | • Check to see if the batteries are loaded in the | 8 | |||||||
|
|
|
|
|
|
| remote controller in opposite direction. | ||
•Check to see if the batteries in the remote controller are OK.
ENGLISH
23
