Manuals / Brands / Computer Equipment / Barcode Reader / Honeywell / Computer Equipment / Barcode Reader

Honeywell 1300g RS232 Timeout, XON/XOFF, ACK/NAK, Save, XON/XOFF On, XON/XOFF On, XON/XOFF Off, RS232 Timeout, * XON/OFF Off

1 192

Download 192 pages, 1.42 Mb

RS232 Timeout

When using Flow Control with Timeout, you must program the length of the delay you want to wait for CTS from the host. Set the length (in milliseconds) for a timeout by scanning the bar code below, then setting the timeout (from 1- 65535 milliseconds) by scanning digits from the inside back cover, then scanning Save. Default = 1000.

RS232 Timeout

XON/XOFF

Standard ASCII control characters can be used to tell the scanner to start sending data (XON/XOFF On) or to stop sending data (XON/XOFF Off). When the host sends the XOFF character (DC3, hex 13) to the scanner, data transmission stops. To resume transmission, the host sends the XON character (DC1, hex 11). Data transmission continues where it left off when XOFF was sent. Default

=XON/XOFF Off.

XON/XOFF On

* XON/OFF Off

ACK/NAK

After transmitting data, the scanner waits for an ACK character (hex 06) or a NAK character (hex 15) response from the host. If ACK is received, the communications cycle is completed and the scanner looks for more bar codes. If NAK is received, the last set of bar code data is retransmitted and the scanner waits

2 - 27

Contents

Page Disclaimer Table of Contents Chapter 1 - Getting Started About This Manual Unpacking the Scanner Connecting with USB Chapter 3 - Input/Output Settings Good Read Indicators Beeper – Good Read Trigger Modes Manual/Serial Trigger Chapter 4 - Data Editing To Add a Prefix or Suffix To Add a Carriage Return Suffix to All Symbologies4 Prefix Selections Suffix Selections Chapter 6 - Symbologies All Symbologies Code 39 Start/Stop Characters Code 39 Append Full ASCII Code 39 Code Page Chapter 7 - Interface Keys Chapter 8 - Utilities Chapter 9 - Serial Programming Commands Conventions Menu Commands Chapter 10 - Product Specifications Hyperion 1300g Product Specifications Standard Connector Pinouts Chapter 11 - Maintenance Repairs Page Getting Started Connecting with Keyboard Wedge Connecting with RS-232Serial Port Connecting with RS485 Reading Techniques Good Technique Bad Technique Menu Bar Code Security Settings Setting Custom Defaults Set Custom Defaults Set Custom Defaults Resetting the Custom Defaults Page Programming the Interface Keyboard Wedge Laptop Direct Connect RS232 Serial Port RS485 OPOS Mode USB IBM SurePos USB PC or Macintosh Keyboard USB HID POS USB Serial Emulation CTS/RTS Emulation ACK/NAK Mode Datalogic™ Magellan® Bioptic Aux Port Configuration Datalogic Magellan Bioptic Settings Wincor Mode A Wincor Mode A Keyboard Country Layout * United States Albania Arabic Azeri (Cyrillic) Page Page Page Page Page Page Page Page Page ALT Mode Keyboard Style Keyboard Modifiers Windows Mode Prefix/Suffix Off: Windows Mode Control + Mode On * Control + X Mode Off DOS Mode Control + X Mode Numeric Keypad Mode: Numeric Keypad Mode On * Numeric Keypad Mode Off Automatic Direct Connect Mode: Automatic Direct RS-232Baud Rate RS-232Word Length: Data Bits, Stop Bits, and Parity 7 Data, 1 Stop, Parity Odd 7 Data, 2 Stop Parity None 7 Data, 2 Stop, Parity Even 7 Data, 2 Stop, Parity Odd RS-232Handshaking RTS/CTS Off: RTS/CTS Off, RTS Inactive: Flow Control, No Timeout: Two-Direction Flow Control: Flow Control with Timeout: Page RS232 Timeout XON/XOFF ACK/NAK Scanner-BiopticPacket Mode Input/Output Settings Beeper – Good Read Beeper Volume – Good Read Beeper Pitch – Good Read Beeper Duration – Good Read Beeper Pitch – Error LED – Good Read Number of Beeps – Good Read User-SpecifiedGood Read Delay Manual/Serial Trigger Read Time-Out Automatic Trigger Presentation Mode Continuous Illumination Mode (Manual Trigger only) Hands Free Time-Out Hands Free Time-Out Reread Delay Short (500 ms) * Medium (750 ms) Long (1000 ms) Extra Long (2000 ms) User-SpecifiedReread Delay Page To Add an Output Sequence Other Programming Selections Output Sequence Editor Output Sequence Example Page Require Output Sequence Off No Read Video Reverse VIDREV0REV Page Data Editing Points to Keep In Mind To Add a Prefix or Suffix Example: Add a Tab Suffix to All Symbologies To Clear One or All Prefixes or Suffixes To Add a Carriage Return Suffix to All Symbologies Prefix Selections Suffix Selections Alternate Extended ASCII Characters DEC HEX Keyboard Function Function Code Transmit Intercharacter Delay User Specified Intercharacter Delay Interfunction Delay Intermessage Delay Page Page Data Formatting To Add a Data Format Other Programming Selections Clear All Data Formats Send Commands Send all characters Send a number of characters Send all characters up to a particular character Send all but the last characters Insert a character multiple times Insert symbology name Insert bar code length Move Commands Move the cursor forward a number of characters Move the cursor backward a number of characters Move the cursor to the beginning Move the cursor to the end Search Commands Search forward for a character Search backward for a character Search forward for a string Search backward for a string Search forward for a non-matchingcharacter Search backward for a non-matchingcharacter Miscellaneous Commands Suppress characters Stop suppressing characters Replace characters Stop replacing characters Compare characters Compare string Check for a number Check for non-numericcharacter Insert a delay Data Format Editor Data Formatter *Data Formatter On, but Not Required Data Formatter Off Data Format On, Format Required Page Symbologies All Symbologies All Symbologies On All Symbologies On All Symbologies Off Message Length <Default All Codabar Settings Codabar Codabar Start/Stop Characters Codabar Check Character Codabar Concatenation Codabar Message Length < Default All Code 39 Settings Code 39 Start/Stop Characters Code 39 Check Character Code 39 Message Length Code 39 Append Code 32 Pharmaceutical (PARAF) Full ASCII Code 39 Code Page < Default All Interleaved 2 of 5 Settings Interleaved 2 of Check Digit Interleaved 2 of 5 Message Length < Default All Code 93 Settings Code 93 Message Length Code 93 Code Page Code 93 Code Page <Default All Straight 2 of 5 Settings Straight 2 of 5 Industrial Straight 2 of 5 Industrial Message Length <Default All Code IATA 2 of 5 Settings Straight 2 of 5 IATA Straight 2 of 5 IATA Message Length <Default All Matrix 2 of 5 Settings Matrix 2 of Matrix 2 of 5 Message Length <Default All Code 11 Settings Check Digits Required Code 11 Message Length <Default All Code 128 Settings ISBT 128 Concatenation Code 128 Message Length Code 128 Code Page Code 128 Function Code Transmit <Default All Telepen Settings Telepen Telepen Output Telepen Message Length <Default All UPC A Settings UPC A UPC A Check Digit UPC A Number System UPC A Addenda UPC A Addenda Required UPC A Addenda Separator UPC-A/EAN-13 with Extended Coupon Code and <Default All UPC E Settings UPC E0 and UPC E1 UPC E0 and UPC E1 Expand UPC E0 and UPC E1 Addenda Required UPC E0 and UPC E1 Addenda Separator UPC E0 Check Digit UPC E0 Number System UPC E0 Addenda <Default All EAN/JAN Settings EAN/JAN 13 Check Digit EAN/JAN 13 Addenda EAN/JAN 13 Addenda Required EAN/JAN 13 Addenda Separator ISBN Translate <Default All EAN/JAN 8 Settings EAN/JAN 8 Check Digit EAN/JAN 8 Addenda EAN/JAN 8 Addenda Required EAN/JAN 8 Addenda Separator <Default All MSI Settings MSI MSI Check Character MSI Message Length <Default All Plessey Code Settings Plessey Code Plessey Message Length < Default All GS1 DataBar Omnidirectional Settings GS1 DataBar Omnidirectional < Default All GS1 DataBar Limited Settings GS1 DataBar Limited < Default All GS1 DataBar Expanded Settings GS1 DataBar Expanded GS1 DataBar Expanded Message Length <Default All China Post Code Settings China Post Code China Post Message Length <Default All Korea Post Code Settings Korea Post Code Korea Post Message Length <Default All Codablock F Settings Codablock F Codablock F Message Length <Default All Code 49 Settings Code 49 Message Length Trioptic Code GS1 Emulation GS1 Data Bar Emulation GS1-128Emulation * GS1 Emulation Off Label Code Page Interface Keys Supported Interface Keys IBM AT/XT and PS/2 Compatibles WYSE PC/AT Supported Keys Apple Mac/iMac Page Utilities EZConfig-ScanningOperations Scan Data Configure Installing EZConfig-Scanningfrom the Web EZConfig-Scanning Resetting the Standard Product Defaults Remove Custom Defaults Activate Defaults Page Serial Programming Commands Query Commands Concatenation of Multiple Commands Responses Examples of Query Commands Trigger Commands SYN T CR SYN U CR Product Default Settings Programming the Interface Page Page Page Page Page Output Selections Page Page Prefix/Suffix Selections Data Formatter Selections Symbologies Page Page Page Page Page Page Page Product Specifications Parameter Specification Keyboard Wedge Serial Output USB Required Safety Label Locations Light Source Page Maintenance Cleaning the Device Inspecting Cords and Connectors Replacing the Interface Cable Replacing the Interface Cable: Page Page Customer Support Page Appendix A Linear Symbologies Page Postal Symbologies Page Lower ASCII Reference Table Printable Characters Extended ASCII Characters ASCII Alternate Extended PS2 Scan Code Extended ASCII Characters (Continued) Page ISO 2022/ISO 646 Character Replacements Code Page Selection Standard Keyboard Honeywell Page Page Unicode Key Maps 104 Key U.S. Style Keyboard 105 Key European Style Keyboard Page Codabar Straight 2 of 5 Industrial Matrix 2 of GS1 DataBar Page Save Page Honeywell Scanning & Mobility