3 Wiring continued
A Power |
| B Communication |
The power requirement range for the AirAlertTM96d controller is 24 Vdc, 500 mA. The system must be grounded to the power supply. A dedicated circuit breaker should be used. Use 14 AWG two conductor, stranded cable (Belden 5100UE or equivalent), up to 1,000 ft.
If the controller is sharing a power supply with multiple sensors on the network, care must be taken to observe voltage drops (line loss) on the power cable. Supply voltages less than 17 Vdc can render some network devices inoperable. Any supply voltage less than 17 Vdc requires the installation of an additional power supply at that point on the power cable.
Depending on total power consumption, avoid |
|
| |||||||||||||||||||||
powering more than 10 network devices with one |
|
| |||||||||||||||||||||
power supply. Additional power supplies and/or |
|
| |||||||||||||||||||||
decreased number of network devices may be |
|
| |||||||||||||||||||||
required to compensate for line loss. Contact |
|
| |||||||||||||||||||||
Honeywell Analytics for help with all power |
|
| |||||||||||||||||||||
requirements. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| RC | |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Note: Terminal J27 must be grounded to |
| R | |||||||||||||||||||||
|
| ||||||||||||||||||||||
mechanical ground. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| J23 |
Figure 5. Power Wiring |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
| EOL2 |
| RC | EOL3 |
|
| RC |
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||
|
|
|
|
|
|
|
|
|
|
| R |
|
|
|
| R |
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
|
|
| In |
| Out |
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
| J22 |
|
|
|
|
|
|
|
|
| J23 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
| V+ | V- | V+ | V- |
|
| A1 | B1 | A2 |
|
|
|
| |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
The communication cables have to be grounded using the shield terminal. Up to 32 network devices can be installed on each channel.
Use 24 AWG two conductor, twisted and shielded cable (Belden 9841 or equivalent) for the connection. The network can be up to 2,000 feet per channel. The length of a
The communication cables have to be grounded using the shield terminal. Use twisted and shielded cable #24/2 AWG (Belden 9841) for the connection.
Note: Channel 4 is the slave communication channel to retransmit the MODBUS signal to PLC. No sensor can be connected to this channel.
Figure 6. Communications Wiring
|
|
|
|
| Power | |
EOL3 |
| EOL4 |
| EOL1 | jumper position |
|
|
| RC | Fault | |||
|
|
|
|
| ||
| RC |
|
|
| R |
|
|
|
| RC |
|
| |
|
|
|
|
| TX | |
| R |
|
|
|
| |
|
|
|
|
|
| |
|
|
| R |
|
|
|
|
|
|
|
|
| RX |
A1 B1 A2 B2 SHLD | J24 |
| B3 A4 B4 |
| ||
SHLD A3 |
|
Channel 2 | Channel 4 |
Channel 1 | Channel 3 |
Previous
Communication Requirements:
•24 AWG twisted pair, shielded (Belden 9841 or equivalent)
•Network can be up to 2,000 feet per channel
•Avoid
•Do not exceed 65 feet per
•Do not exceen 130 feet total of all
End-of-line specification:
The E.O.L. jumper for channels
Next
•Communication wire shield must be connected to shield terminal(s) of controller
•Channels
•Channel 4: Modbus output only — No sensor can be connected to Channel 4
Manning | 7 |