Horizon Fitness R3 manual Step B Step D

INTRODUCTION IMPORTANT PRECAUTIONS

ASSEMBLY

A S S E M B LY STEP 4
STEP B	STEP D
	SEAT FRAME	SEAT LEVER
	SEAT GUIDE RAIL
SEAT BASE
SEAT FRAME
	SEAT LEVER CLAMP
	NOTE: Be sure to keep SEAT LEVER positioned upward as
WAVY WASHERS (G)	shown. Orientate SEAT LEVER CLAMP with rounded edge
BOLTS (F)	facing away from SEAT GUIDE RAIL as shown above.

A S S E M B LY STEP 5
RECESS	EXPOSED WIRES
COVERED WIRE	LOWER HANDLEBAR
	BOLTS (E)
	SPRING WASHERS (B)
	PULSE GRIP WIRES
WIRE CLIP	SEAT FRAME WIRES

IMPORTANT PRECAUTIONS INTRODUCTION

ASSEMBLY

BEFORE YOU BEGIN

BIKE OPERATION

PRE-ATTACHED WASHERS

PRE-ATTACHED SPRING WASHERS

PRE-ATTACHED BOLTS

SEAT GUIDE RAIL CAP

RUBBER STOPPER

SCREW (H)

SEAT GUIDE RAIL

CAP

BASE FRAME

SEAT BACK

WAVY WASHERS (G)

BOLTS (F)

BEFORE YOU BEGIN

BIKE OPERATION

CONDITIONING TROUBLESHOOTING LIMITED

GUIDELINES & MAINTENANCE WARRANTY

10

AOpen HARDWARE BAG FOR STEP 4.

BAttach the SEAT BASE to the SEAT FRAME using 4 BOLTS (F) and 4 WAVY WASHERS (G).

CRemove SEAT GUIDE RAIL CAPS, then remove the PRE-ATTACHED BOLTS, SPRING WASHERS and WASHERS from both ends of the SEAT GUIDE RAIL and lift from base frame. Note the orientation of the seat guide rail.

DSlide the SEAT FRAME through the rear of the SEAT GUIDE RAIL as shown above. Lock SEAT FRAME into place by pushing down on SEAT LEVER. NOTE: Seat lever will face forward when in locked position.

EAttach the RUBBER STOPPER to the bottom of the SEAT GUIDE RAIL using 1 SCREW (H).

FSet assembled SEAT GUIDE RAIL on the grooves of the BASE FRAME.

GRe-attach the PRE-ATTACHED BOLTS, SPRING WASHERS and WASHERS through the BASE FRAME into each end of the SEAT GUIDE RAIL. DO NOT TIGHTEN UNTIL ALL FOUR BOLTS HAVE BEEN STARTED.

HSnap SEAT GUIDE RAIL CAPS back onto each end of SEAT GUIDE RAIL.

HARDWARE BAG FOR STEP 4 CONTENTS :

BOLT (F)	WAVY WASHER (G)	SCREW (H)	RUBBER STOPPER
35 mm	18 mm	8 mm	Qty: 1
Qty: 4	Side View Qty: 4	Qty: 1

A Open HARDWARE BAG FOR STEP 5.

BConnect the SEAT FRAME WIRES to the PULSE GRIP WIRES as shown above.

CPress COVERED WIRE into WIRE CLIP just before EXPOSED WIRES as shown above. Tuck EXPOSED WIRES under RECESS in LOWER HANDLEBAR.

DAttach the LOWER HANDLEBAR to the SEAT FRAME using 4 BOLTS (E) and 4 SPRING WASHERS (B).

DO NOT PINCH WIRES!

EAttach the SEAT BACK to the SEAT FRAME using 4 BOLTS (F) and 4 WAVY WASHERS (G).

HARDWARE BAG FOR STEP 5 CONTENTS :

BOLT (E)	SPRING WASHER (B)	BOLT (F)	WAVY WASHER (G)
15 mm	15.4 mm	35 mm	18 mm
Qty: 4	Qty: 4	Qty: 4	Side View Qty: 4

11

LIMITED TROUBLESHOOTING CONDITIONING WARRANTY & MAINTENANCE GUIDELINES

H-Series_R3_Rev.1.6.indd 10-11 7/17/08 3:04:13 PM