Manuals / HP / Computer Equipment / Switch

HP 5200zl manual LED status indicators for 3500yl and 6200yl series

Models: 5200zl 3500yl

1 65

Download 65 pages 15.2 Kb

Page 61

The LED status indicators for the HP ProCurve Switch 5400zl series switch modules are described in the following table.

LED	State	Indication
Link	On (green)	Indicates the port is enabled and receiving a link beat signal
		(for the twisted-pair ports), or a strong enough light level (for
		the fiber-optic ports) from the connected device

	Off	Indicates no active network cable is connected to the port, the
		port is not receiving link beat or sufficient light, or the port has
		been disabled

	Blinking (orange)	If the port LED is blinking simultaneously with the Fault LED,
		the corresponding port has failed its self-test.

Mode	Depending on the mode selected, displays:
	• Network activity information
	• Whether the port is configured for Full Duplex operation
	• Maximum speed operation
	• Whether PoE power is being supplied or not

Table 11. LED status indicators for HP ProCurve Switch 5400zl series—switch modules

LED status indicators for 3500yl and 6200yl series

The front panel of the HP ProCurve Switch 3500yl and 6200yl series has various LED status indicators that are described in the following table.

LED	State
Power	On (green)

	Off

Fault	On (orange)

	Off

	Blinking (orange)

Test	On (green)

	Off

	Blinking (orange)

Indication

The switch is receiving power.

The switch is NOT receiving power.

On briefly after the switch is powered on or reset, at the beginning of switch self-test. If this LED is on for a prolonged time, the switch has encountered a fatal hardware failure, or has failed its self-test.

The normal state; indicates there are no fault conditions on the switch.

A fault has occurred on the switch, one of the switch ports, module in the rear of the switch, or the fan. The status LED for that component will blink simultaneously.

The switch self-test and initialization are in progress after the switch has been power cycled or reset. The switch is not operational until this LED goes off. The Self Test LED also comes on briefly when you “hot swap” a mini-GBIC into the switch; the mini-GBIC is self-tested when it is hot swapped.

The normal operational state; the switch is not undergoing self test.

A component of the switch has failed its self-test. The status LED for that component will blink simultaneously.

61

Image 61

HP 5200zl manual LED status indicators for 3500yl and 6200yl series

Contents

HP ProCurve Switch 5400zl, 3500yl, and 6200yl Series Ospf Page Introduction Executive summaryOverview Product positioningHP ProCurve Switch 6200yl-24G-mGBIC HP ProCurve Switch 5400zl and 3500yl SeriesProVision Asic architecture Classification and lookup Inside the ProVision Asic ArchitecturePolicy Enforcement Engine Advanced capabilities of the product family Management subsystemHP ProCurve Switch 5400zl Series 5400zl chassis layout ProCurve Switch 5400zl ChassisHP ProCurve Switch 5406zl chassis layout Power supply types System PoE power Power suppliesFan tray Management module Zl modulesHP ProCurve Switch 5400zl series line interface modules Power supply configurations5406zl 5412zl Specifications Memory ProcessorConsole port Auxiliary portPorts DescriptionMini-GBICs supported ordered separately Open mini-GBIC slots Maximum distance Transceivers supported ordered separatelyHP ProCurve Radio Ports supported ordered separately HP ProCurve ONE Services zl Module J9289A DescriptionHP ProCurve Switch 3500yl Series Page Additional line interface module LED status indicatorsHP ProCurve Switch 6200yl HP ProCurve Switch 6200yl-24G-mGBIC J8992A Security features Overview of features and benefitsPerformance QoS functions Bandwidth shaping usingConvergence Advanced classifier-based QoSBridging protocols Layer 2 switchingRouting protocols IPv6Management DiagnosticsFuture-proofing Low cost of ownershipDevice management Standards and protocolsGeneral protocols IP MulticastNetwork management MIBsPerformance and capacity Capacity and performance features comparisonQoS/Cos SecurityPer-port buffer sizes Optimizing the 10-GbE port configuration Page Throughput and latency performance data Gbps Gigabit performance traffic patterns Industry-leading warranty HP ProCurve warranty and supportIntelligent Edge and Premium License Appendix a Premium LicenseTask Manual Using Appendix B Policy Enforcement Engine Policy Enforcement Engine benefits Wire-speed performance for ACLsGranular policy enforcement Hardware-based performancePoE device types Appendix C Power over EthernetAdditional PoE power-external supplies Power delivery optionsPoE negotiation Support for pre-802.3af standard powered devices Appendix D PIM Sparse ModeAppendix E LLDP-MED Appendix F Virus Throttle security Page Response options Appendix G VrrpSensitivity Connection-rate ACLXrrp support on 5300xl switch Appendix H Ospf Equal Cost Multipath Vlan ID Appendix I Advanced Classifier-Based QoSLimitations/Restrictions Appendix J Server-to-Switch Distributed TrunkingLED status indicators for 5400zl series Appendix K TroubleshootingAn example of upstream traffic forwarding is as follows EPS LED LED status indicators for 3500yl and 6200yl series Temp On green Blinking orange Fan Status PoE Status Off Part number Component Part numbers and Field Replaceable UnitsPart number Component For more information