Troubleshooting

Chapter 11

The "Using Correct Type of Phone Cord with Fax" test failed

Solution

Make sure you used the phone cord supplied in the box with your HP All-in- One to connect to the telephone wall jack. One end of the phone cord should be connected to the port labeled "1-LINE" on the back of your HP All-in-One and the other end to your telephone wall jack, as shown below.

1 Telephone wall jack

2 Phone cord supplied in the box with your HP All-in-One

If the supplied phone cord is not long enough, you can extend it. For information see The phone cord that came with my HP All-in-One is not long enough.

Check the connection between the telephone wall jack and the HP All-in-One to make sure the phone cord is secure.

The "Dial Tone Detection" test failed

Solution

Other equipment, which uses the same phone line as the HP All-in-One, might be causing the test to fail. To find out if other equipment is causing a problem, disconnect everything from the phone line, and then run the test again. If the Dial Tone Detection Test passes without the other equipment, then one or more pieces of the equipment is causing problems; try adding them back one at a time and rerunning the test each time, until you identify which piece of equipment is causing the problem.

Try connecting a working phone and phone cord to the telephone wall jack that you are using for the HP All-in-One and check for a dial tone. If you do not hear a dial tone, contact your telephone company and have them check the line.

Make sure you have correctly connected the HP All-in-One to the telephone wall jack. Using the phone cord supplied in the box with your HP All-in-One, connect one end to your telephone wall jack, then connect the other end to the port labeled "1-LINE" on the back of your HP All-in-One. For more information on setting up your HP All-in-One for faxing, see Fax setup.

102

HP Officejet 5600 All-in-One series

Page 105
Image 105
HP 5610v, 5610xi, 5605 manual Using Correct Type of Phone Cord with Fax test failed, Dial Tone Detection test failed

5610, 5610v, 5605, 5610xi specifications

The HP 5605, 5610v, and 5610xi are integral components of HP's versatile line of managed networking equipment, primarily aimed at delivering robust performance for small to medium-sized businesses. Built with a focus on reliability and efficiency, these models cater to the increasing demands of today's network environments.

One of the main features of the HP 5605 is its capacity as a Layer 3 switch, allowing for efficient management of traffic between multiple networks. With the potential to support Virtual LANs (VLANs), administrators can segment network traffic for better performance and security. The device is equipped with Gigabit Ethernet ports, enabling high-speed connectivity essential for data-intensive applications. Moreover, the HP 5605 provides advanced management features that allow for the customization of network settings to optimize performance per specific business requirements.

Meanwhile, the HP 5610v series enhances networking capabilities through its innovative technologies. It supports advanced routing protocols like Open Shortest Path First (OSPF) and Border Gateway Protocol (BGP), which are crucial for directing traffic efficiently across complex networks. The inclusion of Power over Ethernet (PoE) allows the connection of devices such as IP phones and wireless access points without needing additional power sources. Such conveniences streamline installation and reduce overhead costs.

The HP 5610xi model takes performance a notch higher with its expanded capabilities, tailored for growing networks. It boasts a higher throughput and supports additional features like IPv6 for future-proofing, recognizing the growing need for devices that can handle modern networking demands.

Security is a critical factor and these devices come equipped with various security features including Access Control Lists (ACLs) and options for encrypted connections. This ensures that sensitive data is well protected against unauthorized access.

Overall, the HP 5605, 5610v, and 5610xi are designed to offer reliability, high performance, and advanced functionalities suited to businesses operating in dynamic environments. Their capabilities to support a variety of traffic management protocols, along with the convenience of PoE, make them a valuable addition to any organizational network architecture. With easy management interfaces and robust security options, these models stand out as essential tools for modern networking challenges.