Manuals / Brands / Computer Equipment / Switch / HP / Computer Equipment / Switch

HP ProCurve 6600 LEDs, Table 1-2.Switch LEDs, Introducing the Switch

1 103

Download 103 pages, 2.69 Mb

Introducing the Switch

Introducing the Switch

Front of the Switch

LEDs

Table 1-2. Switch LEDs

Switch LEDs	State	Meaning

Power	On	The power supply is operating properly.
(green)	Blinking1	Power supply failure. Blinking simultaneously with Fault LED
	Off	No power connection.

Fault	Off	The normal state; indicates there are no fault conditions on the switch.
(orange)	Blinking1	A fault has occurred on the switch, one of the switch ports, module in the rear of
	Blinking1
		the switch, or the fan. The Status LED for the component with the Fault LED will blink
		simultaneously.
	On	On briefly after the switch is powered on or reset, at the beginning of switch self
		test. If this LED is on for a prolonged time, the switch has encountered a fatal
		hardware failure, or has failed its self test. See chapter 4, “Troubleshooting” for
		more information.

Locator (blue)	On	The Locator LED is used to locate a specific switch in a area full of switches. The
	Blinking	LED can be set to be on solid or blink for a specified number of minutes (1-1440).
	Off	The default is 30 minutes. Use the command “chassislocate”.

PS	On green	The switch is receiving power.
(green/orange)	Off	The switch is NOT receiving power.
	Blinking	A fault has occurred on one of the power supplies. The PS Status LED, Fault LED,
	orange1	and on the back of the switch the failed power supply LED (PS1 or PS2) will all blink
		simultaneously.

Tmp	On green	Switch temperature is normal.
(green/orange)	Blinking	An over temperature condition has been detected. This is a Fault condition
	Blinking
	orange1	indicating elevated internal temperatures. The Fault LED will blink simultaneously.
	Blinking	This indicates an alert condition indicating critical internal temperatures. The Fault
	orange2	LED will blink simultaneously.
Fan Status	On	Normal operation, all fans are ok.
(green/orange)	Blinking	One of the unit’s fans has failed. The switch Fault LED will be blinking simultaneously.
	orange1
	Blinking	One of the unit’s fans has failed and the switch is in an overtemp condition. The
	orange2	switch Fault LED will be blinking simultaneously.
Fan LED on the fan	Off	Normal operation, all fans are working properly.
tray (orange)	Blinking	One or more of the unit’s fans has failed. The switch Fault LED, fan status LED on
	orange1	the front of the switch, and the fan status LED on the back of the switch will be
		blinking simultaneously.

1-6

Contents

HP ProCurve Series 6600 Switches Page ProCurve Series 6600 Switches Installation and Getting Started Guide Safety Contents 1 Introducing the Switch 2 Installing the Switch 3 Getting Started With Switch Configuration 4 Replacing Components 5 Troubleshooting A Specifications B Cabling and Technology Information C Safety and EMC Regulatory Statements D Recycle Statements Index Introducing the Switch Table Page Front of the Switch Network Ports LEDs the LED Mode Select Button and Indicator LEDs Reset Button Clear Button Console Port Back of the Switch Power Connector Switch Features console interface web browser ProCurve Manager Installing the Switch Included Parts J a p a n P o w e r C o r d W a r n i n g Installation Precautions: Installation Procedures Summary 1. Prepare the Installation Site 2. Verify the Switch Passes Self Test Figure 2-2.Connecting the power cord N o t e Figure 2-3.Checking the LEDs on the 6600-24Gand 6600-24G-4XG Figure 2-4.Checking the LEDs on the 6600-24XG LED Behavior: During the self test: When the self test completes successfully: Power Fan Status 3. (Optional) Reversing the air flow Page 4. Mount the Switch Figure 2-5.Mounting in a two post rack using the balanced option Figure 2-6.Example attaching mounting brackets Figure 2-7.Installing the rail mounting holding brackets Figure 2-8.Mounting rails in a four-postHP 10K rack Figure 2-9.Sliding the switch into the rails Figure 2-10.Mounting in a rack 5. Connect the Switch to a Power Source 6. (Optional) Install or Remove mini-GBICsor SFPs N o t e s Figure 2-11.One meter DAC Installing the Mini-GBICsor SFP+ Transceivers: Figure 2-12.Installing a Mini-GBICor SFP SFP and SFP+ transceivers Plug-in,Fault and Alert behaviors Removing the mini-GBICs: 7. Connect the Network Cables Figure Connecting a Fiber cable connector 8. (Optional) Connect a Console to the Switch Out-of-band: In-Band: the Switch Terminal Configuration Direct Console Access Figure 2-15.Connecting the console cable Figure 2-16.Connecting the console cable the Installing Console Cable Pinouts Figure 2-17. RJ-45to DB-9pinouts Switch Sample Network Topology Figure 2-19.Example topology Page Getting Started With Switch Configuration Recommended Minimal Configuration Using the Console Setup Screen IP Config (DHCP/Bootp) Manual IP Address Subnet Mask ave Where to Go From Here To Recover from a Lost Manager Password Using the IP Address for Remote Switch Management Starting a Telnet Session Starting a Web Browser Session Page Replacing Components Replacing the fan tray assembly Figure 4-1.Fan tray assembly retaining screws Figure 4-2.Removing the fan tray assembly Replacing the Battery Installing a New Battery AT T E N T I O N Replacing the Power Supplies Page Troubleshooting Basic Troubleshooting Tips Faulty or loose cables Non-standard cables Trunking Check the port configuration www.procurve.com/library Diagnosing with the LEDs Diagnostic Tips: Page Page Proactive Networking Hardware Diagnostic Tests Testing the Switch by Resetting It Testing Twisted-PairCabling Testing Switch-to-DeviceNetwork Communications Testing End-to-EndNetwork Communications Restoring the Factory Default Configuration Downloading New Switch Software HP Customer Support Services Before Calling Support Specifications Physical Electrical Environmental Acoustic Safety Page Page Cabling and Technology Information Cabling specifications Cabling and Technology Technology distance specifications Mode Conditioning Patch Cord Installing the Patch Cord Twisted-PairCable/Connector Pin-Outs Straight-Through Twisted-PairCable for 10 Mbps or 100 Mbps Network Connections Crossover Twisted-PairCable for 10 Mbps or 100 Mbps Network Connection Straight-Through Twisted-PairCable for 1000 Mbps Network Connections Page Safety and EMC Regulatory Statements Safety Information Informations concernant la sécurité Hinweise zur Sicherheit Considerazioni sulla sicurezza Consideraciones sobre seguridad Safety Information (Japan) Safety Information (China) EMC Regulatory Statements Canada Australia/New Zealand Japan Taiwan European Community Page Recycle Statements Waste Electrical and Electronic Equipment (WEEE) Statements Page Page Page Index Numerics Page Page Page Page Page *5992-4962