Manuals / Brands / Computer Equipment / Switch / HP / Computer Equipment / Switch

HP ProCurve 6600 Switch the Installing, Figure 2-6.Example attaching mounting brackets, Figure 2-5.Mounting in a two post rack using the balanced option

1 103

Download 103 pages, 2.69 Mb

Installing the Switch

Installation Procedures

Figure 2-5. Mounting in a two post rack using the balanced option.

1.Use a #1 Phillips (cross-head) screwdriver and attach the mounting brackets to the switch with the included 8-mm M4 screws. Remember to use the correct accessory kit for your switch, see page 2-1.

8 mm

M4 screws

Figure 2-6. Example attaching mounting brackets

Switch the Installing

2-11

Contents

HP ProCurve Series 6600 Switches Page ProCurve Series 6600 Switches Installation and Getting Started Guide Safety Contents 1 Introducing the Switch 2 Installing the Switch 3 Getting Started With Switch Configuration 4 Replacing Components 5 Troubleshooting A Specifications B Cabling and Technology Information C Safety and EMC Regulatory Statements D Recycle Statements Index Introducing the Switch Table Page Front of the Switch Network Ports LEDs the LED Mode Select Button and Indicator LEDs Reset Button Clear Button Console Port Back of the Switch Power Connector Switch Features console interface web browser ProCurve Manager Installing the Switch Included Parts J a p a n P o w e r C o r d W a r n i n g Installation Precautions: Installation Procedures Summary 1. Prepare the Installation Site 2. Verify the Switch Passes Self Test Figure 2-2.Connecting the power cord N o t e Figure 2-3.Checking the LEDs on the 6600-24Gand 6600-24G-4XG Figure 2-4.Checking the LEDs on the 6600-24XG LED Behavior: During the self test: When the self test completes successfully: Power Fan Status 3. (Optional) Reversing the air flow Page 4. Mount the Switch Figure 2-5.Mounting in a two post rack using the balanced option Figure 2-6.Example attaching mounting brackets Figure 2-7.Installing the rail mounting holding brackets Figure 2-8.Mounting rails in a four-postHP 10K rack Figure 2-9.Sliding the switch into the rails Figure 2-10.Mounting in a rack 5. Connect the Switch to a Power Source 6. (Optional) Install or Remove mini-GBICsor SFPs N o t e s Figure 2-11.One meter DAC Installing the Mini-GBICsor SFP+ Transceivers: Figure 2-12.Installing a Mini-GBICor SFP SFP and SFP+ transceivers Plug-in,Fault and Alert behaviors Removing the mini-GBICs: 7. Connect the Network Cables Figure Connecting a Fiber cable connector 8. (Optional) Connect a Console to the Switch Out-of-band: In-Band: the Switch Terminal Configuration Direct Console Access Figure 2-15.Connecting the console cable Figure 2-16.Connecting the console cable the Installing Console Cable Pinouts Figure 2-17. RJ-45to DB-9pinouts Switch Sample Network Topology Figure 2-19.Example topology Page Getting Started With Switch Configuration Recommended Minimal Configuration Using the Console Setup Screen IP Config (DHCP/Bootp) Manual IP Address Subnet Mask ave Where to Go From Here To Recover from a Lost Manager Password Using the IP Address for Remote Switch Management Starting a Telnet Session Starting a Web Browser Session Page Replacing Components Replacing the fan tray assembly Figure 4-1.Fan tray assembly retaining screws Figure 4-2.Removing the fan tray assembly Replacing the Battery Installing a New Battery AT T E N T I O N Replacing the Power Supplies Page Troubleshooting Basic Troubleshooting Tips Faulty or loose cables Non-standard cables Trunking Check the port configuration www.procurve.com/library Diagnosing with the LEDs Diagnostic Tips: Page Page Proactive Networking Hardware Diagnostic Tests Testing the Switch by Resetting It Testing Twisted-PairCabling Testing Switch-to-DeviceNetwork Communications Testing End-to-EndNetwork Communications Restoring the Factory Default Configuration Downloading New Switch Software HP Customer Support Services Before Calling Support Specifications Physical Electrical Environmental Acoustic Safety Page Page Cabling and Technology Information Cabling specifications Cabling and Technology Technology distance specifications Mode Conditioning Patch Cord Installing the Patch Cord Twisted-PairCable/Connector Pin-Outs Straight-Through Twisted-PairCable for 10 Mbps or 100 Mbps Network Connections Crossover Twisted-PairCable for 10 Mbps or 100 Mbps Network Connection Straight-Through Twisted-PairCable for 1000 Mbps Network Connections Page Safety and EMC Regulatory Statements Safety Information Informations concernant la sécurité Hinweise zur Sicherheit Considerazioni sulla sicurezza Consideraciones sobre seguridad Safety Information (Japan) Safety Information (China) EMC Regulatory Statements Canada Australia/New Zealand Japan Taiwan European Community Page Recycle Statements Waste Electrical and Electronic Equipment (WEEE) Statements Page Page Page Index Numerics Page Page Page Page Page *5992-4962