Manuals / HP / Computer Equipment / Printer

HP Latex 260 61-in ( L26500 61-in ) manual Restart the printer

Models: Latex 260 61-in Japan ( L26500 61-in Japan ) Latex 260 61-in ( L26500 61-in )

1 95

Download 95 pages 49.28 Kb

Page 16

Introduction

When you turn off the printer this way, the printheads are automatically stored with the printhead cleaning cartridge, which prevents them from drying out.

However, if you plan to leave the printer turned off for a long period of time, you are recommended to turn it off using the Power button, and then also turn off the power switch at the rear.

To turn it back on later, use the power switch at the rear, and then press the Power button.

When the printer is turned on, it takes about 5 minutes to initialize itself.

Restart the printer

In some circumstances you may be advised to restart the printer. Please proceed as follows:

1.Press the Power button on the front panel to turn the printer off. Wait a few moments, then press the Power button again. This should restart the printer. If it does not, continue with step 2.

2.Use the Reset button on the front panel. You will need a non-conductive implement with a narrow tip to press the Reset button. This normally has the same effect as pressing the Power button, but may work if the Power button does not.

3.If neither steps 1 nor 2 seems to have any effect, turn off the printer by using the power switch at the rear of the printer. Check that the residual current circuit breakers are in the up position.

4.Remove the power cords from the power sockets.

5.Wait for 10 seconds.

6.Reinsert the power cords into the power sockets and turn on the printer by using the power switch.

7.Make sure that the Power light on the front panel illuminates. If it does not, use the Power button to turn on the printer.

12 Chapter 1 Introduction

ENWW

Image 16

$HP Latex 260 61-in ( L26500 61-in ), Latex 260 61-in Japan ( L26500 61-in Japan ) manual Restart the printer$

Contents

Designjet L26500 / L26100 printer series Legal notices TrademarksTable of contents Ink system Safety precautions General safety guidelinesIntroduction Electrical shock hazardHeat hazard Fire hazardHeavy substrate hazard Mechanical hazardInk handling Introduction Printer’s main features Printer’s main componentsFront view Rear view Edge holders caseDrying enclosure Take-up reel motor Loading accessory Front panelEmbedded Web Server Setup tab Turn the printer on and offMain tab Support tabRestart the printer Connectivity and software instructions Connection methodConnect to a network Connection type Speed Maximum cable length Other factorsConnectivity Basic setup options Printer setup optionsChange the language of the front panel View or set the date and timeRequest e-mail notification of specific error conditions Change the cool-down delayChange the sleep mode setting Turn the buzzer on or offEmbedded Web Server setup options Restore factory settingsAccess the Embedded Web Server Change the language of the Embedded Web ServerRestrict access to the printer Overview Handle the substrateSubstrate tips Supported substrate families Example HP Heavyweight Coated PaperSubstrate family Description Supported HP substrates Back Pro Specialty materialsPorous substrates Load a roll onto the spindleLift the spindle lock lever to disengage the spindle Load a roll onto the spindle Handle the substrate Load a roll into the printer automatically Handle the substrate Handle the substrate Load a roll into the printer manually Load a roll into the printer manually Select the type of substrate you are loading Load a cut sheet into the printer Unload a roll from the printerTake-up reel Loop-shapersTake-up reel Handle the substrate Handle the substrate Handle the substrate Handle the substrate Handle the substrate Load a roll onto the take-up reel other substrates Handle the substrate Handle the substrate Handle the substrate Handle the substrate Handle the substrate Unload a roll from the take-up reel Handle the substrate Edge holders Loading accessory Loading accessory Handle the substrate Handle the substrate Double-sided printing OutlineDouble-sided printing View information about the substrate Substrate length tracking Enable/disable the length tracking feature Store the substrateDownload media presets Substrate settingsAdd a new substrate Summary Select printer settings and color profile Setting Description If too low If too high Substrate family Drying Curing Heating AutoSubstrat Input Vacuum Temp Airflow TrackingSubstrates in normal Load the substrate and print the diagnostic plot OmasChange settings while printing Advanced settingsLow-temp Mesh Select the number of passes Temperature profileAqueou Check the quantity of ink on the substrate KeySubstrate settings Substrate settings Faster printing Color calibrationColor profiles Color reproduction tricksSubstrate settings Retrieving usage information Get accounting information Check usage statisticsCheck usage statistics for a job Request accounting data by E-mailSet Send accounting files to Enabled Ink system Ink system componentsInk cartridges PrintheadsPrinthead cleaning kit Printhead cleaning cartridgePrinthead cleaning container Ink funnelInk maintenance kit Order ink supplies Cartridge Capacity ml Part numberPrinthead Part number Kit Part numberPrinter states Print optionsChange margins Request the printer’s internal prints Order accessories AccessoriesName Product number Functional specifications Printer specificationsMinimum Maximum Physical specifications Memory specificationsPower specifications Outside Japan Japan onlyEnvironmental specifications Acoustic specificationsGlossary Back tensionPET PVC Index Safety labels