Manuals / HP / Computer Equipment / Printer

HP Latex 260 61-in Japan ( L26500 61-in Japan ) Check the quantity of ink on the substrate, Key

Models: Latex 260 61-in Japan ( L26500 61-in Japan ) Latex 260 61-in ( L26500 61-in )

1 95

Download 95 pages 49.28 Kb

Page 71

Passes	Uni/	Self	Banner	Textile	Film	Synthet	Paper	Paper	Low	Mesh
	bidir	adhesi				ic	aqueou	solvent	temp.
		ve				paper	s

18*	Bidir	Yes	Yes	Yes	Yes	Yes	Yes	Yes	Yes	Yes

20 to 32	Bidir	Yes	Yes	Yes	Yes	Yes	Yes	Yes	Yes	Yes

*Unlike other printmodes, the 18-pass printmode has 1200 dpi x 1200 dpi input data resolution at 1 bpp (1 bit per pixel). Therefore, to generate a 18-pass media preset you should start either from an existing 18-pass preset or from scratch. In the same way, do not clone an 18-pass media preset to generate a preset with a print mode other than 18-pass.

Key

●Bidir: bidirectional

●No: not recommended

●Maybe: may be worth trying for extra speed

●Start here, Yes: recommended

NOTE: More specific settings for many substrates from different vendors are available in the HP Media Finder at http://www.hp.com/go/latexmediafinder/.

Check the quantity of ink on the substrate

Check that the ink quantities in your media preset are adequate. Look at the color patches in the HP diagnostic chart and check that the patches have the correct amount of ink using the guidelines below:

1.Too much ink: There are several possible symptoms of this problem.

● The last two or three scales of the chart look the same.

Substrate settings

ENWW	Add a new substrate 67

Image 71

$HP Latex 260 61-in Japan ( L26500 61-in Japan ) manual Check the quantity of ink on the substrate, Key$

Contents

Designjet L26500 / L26100 printer series Trademarks Legal noticesTable of contents Ink system Electrical shock hazard Safety precautionsGeneral safety guidelines IntroductionFire hazard Heat hazardInk handling Mechanical hazardHeavy substrate hazard Introduction Printer’s main components Printer’s main featuresFront view Edge holders case Rear viewDrying enclosure Take-up reel motor Front panel Loading accessoryEmbedded Web Server Support tab Setup tabTurn the printer on and off Main tabRestart the printer Connection type Speed Maximum cable length Other factors Connectivity and software instructionsConnection method Connect to a networkConnectivity View or set the date and time Basic setup optionsPrinter setup options Change the language of the front panelTurn the buzzer on or off Request e-mail notification of specific error conditionsChange the cool-down delay Change the sleep mode settingChange the language of the Embedded Web Server Embedded Web Server setup optionsRestore factory settings Access the Embedded Web ServerRestrict access to the printer Substrate tips Handle the substrateOverview Substrate family Description Example HP Heavyweight Coated PaperSupported substrate families Supported HP substrates Specialty materials Back ProLoad a roll onto the spindle Porous substratesLift the spindle lock lever to disengage the spindle Load a roll onto the spindle Handle the substrate Load a roll into the printer automatically Handle the substrate Handle the substrate Load a roll into the printer manually Load a roll into the printer manually Select the type of substrate you are loading Unload a roll from the printer Load a cut sheet into the printerLoop-shapers Take-up reelTake-up reel Handle the substrate Handle the substrate Handle the substrate Handle the substrate Handle the substrate Load a roll onto the take-up reel other substrates Handle the substrate Handle the substrate Handle the substrate Handle the substrate Handle the substrate Unload a roll from the take-up reel Handle the substrate Edge holders Loading accessory Loading accessory Handle the substrate Handle the substrate Outline Double-sided printingDouble-sided printing View information about the substrate Substrate length tracking Store the substrate Enable/disable the length tracking featureAdd a new substrate Substrate settingsDownload media presets Summary Select printer settings and color profile Airflow Tracking Setting Description If too low If too highSubstrate family Drying Curing Heating Auto Substrat Input Vacuum TempSubstrates in normal Omas Load the substrate and print the diagnostic plotAdvanced settings Change settings while printingLow-temp Mesh Aqueou Temperature profileSelect the number of passes Key Check the quantity of ink on the substrateSubstrate settings Substrate settings Color calibration Faster printingColor reproduction tricks Color profilesSubstrate settings Retrieving usage information Request accounting data by E-mail Get accounting informationCheck usage statistics Check usage statistics for a jobSet Send accounting files to Enabled Printheads Ink systemInk system components Ink cartridgesPrinthead cleaning cartridge Printhead cleaning kitInk funnel Printhead cleaning containerInk maintenance kit Kit Part number Order ink suppliesCartridge Capacity ml Part number Printhead Part numberChange margins Print optionsPrinter states Request the printer’s internal prints Name Product number AccessoriesOrder accessories Minimum Maximum Printer specificationsFunctional specifications Outside Japan Japan only Physical specificationsMemory specifications Power specificationsAcoustic specifications Environmental specificationsBack tension GlossaryPET PVC Index Safety labels