Manuals / HP / Computer Equipment / Printer

HP Latex 260 61-in Japan ( L26500 61-in Japan ) manual Connectivity and software instructions

Models: Latex 260 61-in Japan ( L26500 61-in Japan ) Latex 260 61-in ( L26500 61-in )

1 95

Download 95 pages 49.28 Kb

Page 17

2Connectivity and software instructions

Connection method

Your printer can be connected in the following way.

Connection type	Speed	Maximum cable length	Other factors

Gigabit Ethernet	Fast; varies according to	Long (100 m=328 ft)	Requires extra equipment
	network traffic		(switches)

NOTE: The speed of any network connection depends on all the components that are used in the network, which can include network interface cards, hubs, routers, switches, and cables. If any one of these components cannot operate at high speed, you will have a low-speed connection. The speed of your network connection can also be affected by the total amount of traffic from other devices on the network.

Connect to a network

Before you begin, check your equipment:

●The printer should be set up and turned on.

●The Gigabit switch or router should be on and functioning correctly.

●All computers on the network should be turned on and connected to the network.

●The printer should be connected to the switch.

When the printer is connected to the network and turned on, you should see the printer's IP address appear on the front panel (192.168.1.1 in this example). Make a note of the IP address: you can use it later to access the Embedded Web Server.

Connectivity

ENWW	Connection method 13

Image 17

$HP Latex 260 61-in Japan ( L26500 61-in Japan ) manual Connectivity and software instructions, Connection method$

Contents

Designjet L26500 / L26100 printer series Trademarks Legal noticesTable of contents Ink system General safety guidelines Safety precautionsIntroduction Electrical shock hazardFire hazard Heat hazardInk handling Mechanical hazardHeavy substrate hazard Introduction Printer’s main components Printer’s main featuresFront view Edge holders case Rear viewDrying enclosure Take-up reel motor Front panel Loading accessoryEmbedded Web Server Turn the printer on and off Setup tabMain tab Support tabRestart the printer Connection method Connectivity and software instructionsConnect to a network Connection type Speed Maximum cable length Other factorsConnectivity Printer setup options Basic setup optionsChange the language of the front panel View or set the date and timeChange the cool-down delay Request e-mail notification of specific error conditionsChange the sleep mode setting Turn the buzzer on or offRestore factory settings Embedded Web Server setup optionsAccess the Embedded Web Server Change the language of the Embedded Web ServerRestrict access to the printer Substrate tips Handle the substrateOverview Substrate family Description Example HP Heavyweight Coated PaperSupported substrate families Supported HP substrates Specialty materials Back ProLoad a roll onto the spindle Porous substratesLift the spindle lock lever to disengage the spindle Load a roll onto the spindle Handle the substrate Load a roll into the printer automatically Handle the substrate Handle the substrate Load a roll into the printer manually Load a roll into the printer manually Select the type of substrate you are loading Unload a roll from the printer Load a cut sheet into the printerLoop-shapers Take-up reelTake-up reel Handle the substrate Handle the substrate Handle the substrate Handle the substrate Handle the substrate Load a roll onto the take-up reel other substrates Handle the substrate Handle the substrate Handle the substrate Handle the substrate Handle the substrate Unload a roll from the take-up reel Handle the substrate Edge holders Loading accessory Loading accessory Handle the substrate Handle the substrate Outline Double-sided printingDouble-sided printing View information about the substrate Substrate length tracking Store the substrate Enable/disable the length tracking featureAdd a new substrate Substrate settingsDownload media presets Summary Select printer settings and color profile Substrate family Drying Curing Heating Auto Setting Description If too low If too highSubstrat Input Vacuum Temp Airflow TrackingSubstrates in normal Omas Load the substrate and print the diagnostic plotAdvanced settings Change settings while printingLow-temp Mesh Aqueou Temperature profileSelect the number of passes Key Check the quantity of ink on the substrateSubstrate settings Substrate settings Color calibration Faster printingColor reproduction tricks Color profilesSubstrate settings Retrieving usage information Check usage statistics Get accounting informationCheck usage statistics for a job Request accounting data by E-mailSet Send accounting files to Enabled Ink system components Ink systemInk cartridges PrintheadsPrinthead cleaning cartridge Printhead cleaning kitInk funnel Printhead cleaning containerInk maintenance kit Cartridge Capacity ml Part number Order ink suppliesPrinthead Part number Kit Part numberChange margins Print optionsPrinter states Request the printer’s internal prints Name Product number AccessoriesOrder accessories Minimum Maximum Printer specificationsFunctional specifications Memory specifications Physical specificationsPower specifications Outside Japan Japan onlyAcoustic specifications Environmental specificationsBack tension GlossaryPET PVC Index Safety labels