Manuals / HP / Computer Equipment / Printer

HP Latex 260 61-in Japan ( L26500 61-in Japan ) Print options, Printer states, Change margins

Models: Latex 260 61-in Japan ( L26500 61-in Japan ) Latex 260 61-in ( L26500 61-in )

1 95

Download 95 pages 49.28 Kb

Page 85

8 Print options

Printer states

The printer may be in any one of the following states; some of them require waiting.

●Ready (cold): The printer is powered on but has not printed yet, and the heaters are not turned on.

●Preparing to print: The printer is warming up the heaters and preparing the printheads to print. This takes 1 to 8 min.

●Ready for substrate

●Ready for side A/B

●Printing

●Printing side A/B

●Curing: This takes 1.5 to 5 min.

●Finishing: The printer is cooling down and preparing for stand-by. This takes 0.5 to 5 min.

If jobs of the same print mode as the already-printed file are sent while the printer is Curing (if the cutter is not enabled) or Finishing, the printer goes to Preparing to print.

To save time between prints, concatenate jobs with the same print mode (same number of passes) and turn the cutter off to skip the Curing and Finishing states. You can also use nesting to print several jobs in the same workflow.

Even if the cutter is on or successive jobs use different print modes, it is better to print them all together without delays to minimize the time spent in Preparing to print.

Change margins

The printer margins determine the area between the edges of your image and the edges of the substrate.

The margins for a particular print job are selected in the RIP software; if the job exceeds the substrate width, it will be clipped.

The front panel offers additional settings for the bottom margin: see Table 10-4 Margins on page 85. These settings apply only to single prints when the cutter is not in use. The bottom margin is not applied between several prints sent at the same time, nor during double-sided printing.

Print options

ENWW	Printer states 81

Image 85

$HP Latex 260 61-in Japan ( L26500 61-in Japan ) manual Print options, Printer states, Change margins$

Contents

Designjet L26500 / L26100 printer series Trademarks Legal noticesTable of contents Ink system General safety guidelines Safety precautionsIntroduction Electrical shock hazardFire hazard Heat hazardHeavy substrate hazard Mechanical hazardInk handling Introduction Printer’s main components Printer’s main featuresFront view Edge holders case Rear viewDrying enclosure Take-up reel motor Front panel Loading accessoryEmbedded Web Server Turn the printer on and off Setup tabMain tab Support tabRestart the printer Connection method Connectivity and software instructionsConnect to a network Connection type Speed Maximum cable length Other factorsConnectivity Printer setup options Basic setup optionsChange the language of the front panel View or set the date and timeChange the cool-down delay Request e-mail notification of specific error conditionsChange the sleep mode setting Turn the buzzer on or offRestore factory settings Embedded Web Server setup optionsAccess the Embedded Web Server Change the language of the Embedded Web ServerRestrict access to the printer Overview Handle the substrateSubstrate tips Supported substrate families Example HP Heavyweight Coated PaperSubstrate family Description Supported HP substrates Specialty materials Back ProLoad a roll onto the spindle Porous substratesLift the spindle lock lever to disengage the spindle Load a roll onto the spindle Handle the substrate Load a roll into the printer automatically Handle the substrate Handle the substrate Load a roll into the printer manually Load a roll into the printer manually Select the type of substrate you are loading Unload a roll from the printer Load a cut sheet into the printerLoop-shapers Take-up reelTake-up reel Handle the substrate Handle the substrate Handle the substrate Handle the substrate Handle the substrate Load a roll onto the take-up reel other substrates Handle the substrate Handle the substrate Handle the substrate Handle the substrate Handle the substrate Unload a roll from the take-up reel Handle the substrate Edge holders Loading accessory Loading accessory Handle the substrate Handle the substrate Outline Double-sided printingDouble-sided printing View information about the substrate Substrate length tracking Store the substrate Enable/disable the length tracking featureDownload media presets Substrate settingsAdd a new substrate Summary Select printer settings and color profile Substrate family Drying Curing Heating Auto Setting Description If too low If too highSubstrat Input Vacuum Temp Airflow TrackingSubstrates in normal Omas Load the substrate and print the diagnostic plotAdvanced settings Change settings while printingLow-temp Mesh Select the number of passes Temperature profileAqueou Key Check the quantity of ink on the substrateSubstrate settings Substrate settings Color calibration Faster printingColor reproduction tricks Color profilesSubstrate settings Retrieving usage information Check usage statistics Get accounting informationCheck usage statistics for a job Request accounting data by E-mailSet Send accounting files to Enabled Ink system components Ink systemInk cartridges PrintheadsPrinthead cleaning cartridge Printhead cleaning kitInk funnel Printhead cleaning containerInk maintenance kit Cartridge Capacity ml Part number Order ink suppliesPrinthead Part number Kit Part numberPrinter states Print optionsChange margins Request the printer’s internal prints Order accessories AccessoriesName Product number Functional specifications Printer specificationsMinimum Maximum Memory specifications Physical specificationsPower specifications Outside Japan Japan onlyAcoustic specifications Environmental specificationsBack tension GlossaryPET PVC Index Safety labels