Manuals / HP / Computer Equipment / Printer

HP Latex 260 61-in Japan ( L26500 61-in Japan ), Latex 260 61-in ( L26500 61-in ) Take-up reel

Models: Latex 260 61-in Japan ( L26500 61-in Japan ) Latex 260 61-in ( L26500 61-in )

1 95

Download 95 pages 49.28 Kb

Page 39

●The light loop-shaper is used with all other substrates. It lies in the substrate loop, supported only by the substrate, unattached at either end. It should be the same width as the substrate; therefore, it is supplied in sections of different widths that can be fitted together. The spindle stops should be used with this loop-shaper.

There are two slightly different procedures for loading a roll onto the take-up reel, depending on which substrate type and therefore which loop-shaper is used: see See Load a roll onto the take-up reel (banner/textile/mesh substrates) on page 35 and Load a roll onto the take-up reel (other substrates) on page 41.

Load a roll onto the take-up reel (banner/textile/mesh substrates)

1.On the printer's front panel, select the icon, then select Take-up reel > Enable take-up reel.

2.The front panel offers you the choice of loading the take-up reel immediately, or during printing.

If you decide to load the take-up reel during printing, familiarize yourself with the procedural steps. Loading the take-up reel during printing requires you to complete the procedure while the printer is feeding and printing substrate. Loading the take-up reel during printing saves approximately 1 m (3 ft) of substrate.

TIP: If you have already loaded the take-up reel, but the printer fails to recognize that it is loaded, you can save some time by selecting Load it during printing.

The following steps assume that you have decided to load immediately. If you decide to load later, during printing, you must complete the same operations without guidance from the front panel.

Handle the substrate

ENWW	The take-up reel 35

Image 39

$HP Latex 260 61-in Japan ( L26500 61-in Japan ), Latex 260 61-in ( L26500 61-in ) manual Take-up reel$

Contents

Designjet L26500 / L26100 printer series Trademarks Legal noticesTable of contents Ink system Electrical shock hazard Safety precautionsGeneral safety guidelines IntroductionFire hazard Heat hazardMechanical hazard Heavy substrate hazardInk handling Introduction Printer’s main components Printer’s main featuresFront view Edge holders case Rear viewDrying enclosure Take-up reel motor Front panel Loading accessoryEmbedded Web Server Support tab Setup tabTurn the printer on and off Main tabRestart the printer Connection type Speed Maximum cable length Other factors Connectivity and software instructionsConnection method Connect to a networkConnectivity View or set the date and time Basic setup optionsPrinter setup options Change the language of the front panelTurn the buzzer on or off Request e-mail notification of specific error conditionsChange the cool-down delay Change the sleep mode settingChange the language of the Embedded Web Server Embedded Web Server setup optionsRestore factory settings Access the Embedded Web ServerRestrict access to the printer Handle the substrate OverviewSubstrate tips Example HP Heavyweight Coated Paper Supported substrate familiesSubstrate family Description Supported HP substrates Specialty materials Back ProLoad a roll onto the spindle Porous substratesLift the spindle lock lever to disengage the spindle Load a roll onto the spindle Handle the substrate Load a roll into the printer automatically Handle the substrate Handle the substrate Load a roll into the printer manually Load a roll into the printer manually Select the type of substrate you are loading Unload a roll from the printer Load a cut sheet into the printerLoop-shapers Take-up reelTake-up reel Handle the substrate Handle the substrate Handle the substrate Handle the substrate Handle the substrate Load a roll onto the take-up reel other substrates Handle the substrate Handle the substrate Handle the substrate Handle the substrate Handle the substrate Unload a roll from the take-up reel Handle the substrate Edge holders Loading accessory Loading accessory Handle the substrate Handle the substrate Outline Double-sided printingDouble-sided printing View information about the substrate Substrate length tracking Store the substrate Enable/disable the length tracking featureSubstrate settings Download media presetsAdd a new substrate Summary Select printer settings and color profile Airflow Tracking Setting Description If too low If too highSubstrate family Drying Curing Heating Auto Substrat Input Vacuum TempSubstrates in normal Omas Load the substrate and print the diagnostic plotAdvanced settings Change settings while printingLow-temp Mesh Temperature profile Select the number of passesAqueou Key Check the quantity of ink on the substrateSubstrate settings Substrate settings Color calibration Faster printingColor reproduction tricks Color profilesSubstrate settings Retrieving usage information Request accounting data by E-mail Get accounting informationCheck usage statistics Check usage statistics for a jobSet Send accounting files to Enabled Printheads Ink systemInk system components Ink cartridgesPrinthead cleaning cartridge Printhead cleaning kitInk funnel Printhead cleaning containerInk maintenance kit Kit Part number Order ink suppliesCartridge Capacity ml Part number Printhead Part numberPrint options Printer statesChange margins Request the printer’s internal prints Accessories Order accessoriesName Product number Printer specifications Functional specificationsMinimum Maximum Outside Japan Japan only Physical specificationsMemory specifications Power specificationsAcoustic specifications Environmental specificationsBack tension GlossaryPET PVC Index Safety labels