Export ALL NAV Data, Delete ALL NAV Data | Humminbird 531374-1_A

www531374..reelsche-1 A - 947 Man.qxd 2/15/2005matic7:54..coPM Pagem70

EXPORT ALL NAV DATA

(Advanced)

Export All Nav Data allows you to export all saved Tracks, Waypoints and Routes to an

MMC/SD card.

To Export All Navigation Data:

1.Make sure you are in Advanced User Mode, and that an optional-purchase MMC/SD card is installed in the slot, then highlight Export All Nav Data on the Navigation main menu.

2.Use the RIGHT 4-WAY Cursor Control key to export all navigation data.

Chart Menu

DELETE ALL NAV DATA

(Advanced)

Delete All Nav Data allows you to delete all saved Tracks, Waypoints and Routes. This menu choice should be used with caution.

To Delete All Navigation Data:

1.Make sure you are in Advanced User Mode, then highlight Delete All Nav Data on the Navigation main menu.

2.Use the RIGHT 4-WAY Cursor Control key to delete all navigation data.

CHART MENU TAB

Press the MENU key twice to access the Main Menu System and then press the RIGHT Cursor key to select the Chart tab.

NOTE: Menu choices will vary depending on system settings such as whether the unit is set for Advanced User mode.

65

Image 70

Humminbird 531374-1_A manual Export ALL NAV Data, Delete ALL NAV Data, Chart Menu TAB, To Export All Navigation Data

Contents

Page Thank You Table of Contents 3D Sonar X-Press Menu Menu System Start-Up Options Menu2D Sonar X-Press Menu Navigation X-Press Menu Setup Menu Tab Chart Menu TabAlarms Menu Tab Views Menu Tab Accessories Menu Tab Troubleshooting 3D Sonar Series IntroductionHOW the 900 Series Works 2D Sonar MULTI-MEDIA Card MMC SD Slot GPS and CartographySD Slot Accessory Bus Accessory BUSInstallation Overview 900 Series has a wide variety of configurations Basic installation tasks that you must perform include Control Head InstallationGimbal Mounting the Control Head Mounting Screws Washer Gimbal Mounting Bracket Cables Routed Near Mounting Bracket Plug Cable Connector Assembly to Back of Control Head Screws provided IN-DASH Mounting the Control Head Plug Cable Connector Assembly to Back of Control Head Transducer Installation Connecting the Control Head Power Cable to the Boat To determine transducer mounting location Transom Transducer InstallationStepped Hull But do not completely tighten To mount the transducer bracket to the boatTo attach the pivot to the transducer Attaching the Bracket To adjust the running position of the transducer To mount the transducer pivot assembly to the bracketNormal Cavitation Fully tightened To route the transom transducer cableReassemble Routing the Cable Trial installation Inside the Hull Transducer InstallationDetermine the transducer mounting location Make sure the position of the transducer is marked Permanently mount the transducerRoute the cable Transducer Mounted Inside the Hull Test and Finish the Transducer Installation Trolling Motor Transducer Installation Hand-tighten only GPS Receiver InstallationIf you have… Then use Follow these steps to stem mount the GPS receiver Access Under Mounting Location Access Under Mounting LocationTo the cable as shown No Access Under Mounting Location Finish Routing the Cable and Check GPS Receiver Operation Install the temperature probe accessory Routing the cable to the control head Testing the System Installation To test the installation Powering UP the Control Head Series 947c 3D Combo Title Screen WHAT’S on the 3D Sonar Display Triplog WHAT’S on the 2D Sonar Display Bait Ball RTS Real Time Sonar Window Real Time Sonar RTS Window Bottom Presentation View KEY POWER/LIGHT KEYKEY Functions Menu KEY Exit KEY View Preset KeysWAY Cursor Control KEY Info KEY Views MARK/GOTO KEYViews available on your 900 Series are 3D/2D Combo View Views and Readouts3D/2D Combo View 2D Sonar View 2D Sonar View 2D Zoom View 2D Zoom View Beam Sonar View Beam Sonar ViewBIRD’S EYE View Bird’s Eye View Chart/Bird’s Eye Combo View with Active Cursor CHART/BIRD’S EYE Combo ViewChart View Chart View with Active Cursor CHART/2D Combo View CHART/3D Combo ViewChart/2D Combo View Chart View with Cursor Present Chart OrientationViewing Cartography Navigation WAYPOINTS, Routes and TracksWaypoints, Routes and Tracks SAVE, EDIT, or Delete a Waypoint Navigate to a Waypoint or Position Chart View with TargetADD a Waypoint Target or Trolling Grid Chart View with Grid SAVE, Edit or Delete a Route EDIT, Delete or Hide Saved Tracks Save or Clear a Current TrackMenu System Sonar Tab, Normal Mode Sonar Tab, Advanced Mode Normal Operation Exit Normal operation by powering your 900 Series offSTART-UP Options Menu Normal Simulator System Status System Status Self Test Accessory Test GPS Diagnostic ViewSimulator Self Test Accessory Test Screen Accessory TestGPS Diagnostic View GPS Diagnostic View Active Side To Adjust Split Screen Position2D Sonar X-PRESS Menu Split Position Sensitivity To adjust the SensitivityTo adjust the Upper Range Upper Range Lower Range Chart SpeedBottom Lock 2D/3D Priority To adjust the Bottom RangeBottom Range To change the 2D/3D Priority Highlight Split Position on the 3D Sonar X-Press Menu 3D Sonar X-PRESS Menu3D Sonar X-Press Menu 3D Bottom Zoom Beam Sensitivity3D Lower Range To Reset 3D View Reset 3D ViewTo adjust the 3D History 3D History Highlight Split Position on the Navigation X-Press Menu Navigation X-Press Menu Save Current Route Save Current TrackClear Current Track Skip Next Waypoint Remove Target Cancel NavigationRemove Grid 3D Bottom Style Sonar Menu TAB2D Sonar Colors 3D Frame Style To change Beam Select 2D Beam SelectFish ID+ To set Fish ID+ To change the Fish ID 3D Reference setting To change the Fish ID Sensitivity settingTo change the RTS Window setting Fish ID Sensitivity KHZ Sensitivity Bottom ViewZoom Width Depth Lines Surface Clutter To change the Noise Filter settingTo change the Max Depth setting Noise Filter Water Type Temperature GraphColor BAR Tracks Navigation Menu TABWaypoints Routes To change the Chart Orientation settingTo change the North Reference setting North Reference Track MIN Distance Trolling Grid RotationTrackpoint Interval MAP Datum Delete ALL NAV Data Chart Menu TABExport ALL NAV Data To Export All Navigation Data LAT/LON Grid Chart Detail LevelMAP Borders Spot Soundings SET MAP Offset Shaded DepthClear MAP Offset Fish ID Alarm Alarms Menu TABDepth Alarm To change the Depth Alarm setting Temp Alarm LOW Battery AlarmOFF Course Alarm Drift Alarm Arrival AlarmAlarm Tone To change the Units Temp setting Setup Menu TABTo change the Units Depth setting Units Depth Units Speed User ModeUnits Distance Language Restore Defaults Triplog ResetSelect Readouts Default Sonar View Customized Sonar View To Select Readouts Local Time Zone Depth OffsetTemp Offset Daylight Saving Time Date Format Position FormatTime Format Nmea Output To turn Nmea Output on or off SonarViews Menu TAB To turn Sonar on or off Troubleshooting Accessories Menu TABSeries Doesn’t Power Up Series Defaults to Simulator with a Transducer Attached Display Problems Control head loses power at high speeds Noise re-appears Finding the Cause of NoiseOther electronic devices Boat’s engine Year Limited Warranty Humminbird Service Policy Series Accessories Returning Your Unit for ServiceFor IN-WARRANTY service, complete the following steps Specifications Operating Frequency Appendix a Contact Humminbird