Humminbird 531374-1

www531374..reelsche-1 A - 947 Man.qxd 2/15/2005matic7:54..coPM Pagem84

900 Series™ Defaults to Simulator with a Transducer Attached

A connected and functioning transducer will cause the newly-started 900 Series™ to go into Normal operating mode automatically. If, when you power up the 900 Series™, it goes into Simulator mode automatically, even though a transducer is already connected, this means that the control head is not detecting the transducer. Perform the following troubleshooting tasks:

•Using the Installation Guide that also comes with your 900 Series™, check to make sure that the transducer cable is securely connected to the 900 Series. Reconnect if necessary, and power up the 900 Series™ again to see if this fixes the problem.

•Replace the non-functioning transducer with a known good transducer if available and power up the control head again.

•Check the transducer cable. Replace the transducer if the cable is damaged or corroded.

Page 84

Image 84

Humminbird 531374-1_A manual Series Defaults to Simulator with a Transducer Attached

Contents

Page Thank You Table of Contents Menu System Start-Up Options Menu 2D Sonar X-Press Menu3D Sonar X-Press Menu Navigation X-Press Menu Chart Menu Tab Alarms Menu TabSetup Menu Tab Views Menu Tab Accessories Menu Tab Troubleshooting Series Introduction HOW the 900 Series Works3D Sonar 2D Sonar GPS and Cartography MULTI-MEDIA Card MMC SD SlotSD Slot Accessory BUS Installation OverviewAccessory Bus 900 Series has a wide variety of configurations Control Head Installation Basic installation tasks that you must perform includeGimbal Mounting the Control Head Mounting Screws Washer Gimbal Mounting Bracket Cables Routed Near Mounting Bracket Plug Cable Connector Assembly to Back of Control Head Screws provided IN-DASH Mounting the Control Head Plug Cable Connector Assembly to Back of Control Head Transducer Installation Connecting the Control Head Power Cable to the Boat Transom Transducer Installation To determine transducer mounting locationStepped Hull To mount the transducer bracket to the boat To attach the pivot to the transducerBut do not completely tighten Attaching the Bracket To mount the transducer pivot assembly to the bracket To adjust the running position of the transducerNormal Cavitation To route the transom transducer cable ReassembleFully tightened Routing the Cable Inside the Hull Transducer Installation Trial installationDetermine the transducer mounting location Permanently mount the transducer Route the cableMake sure the position of the transducer is marked Transducer Mounted Inside the Hull Test and Finish the Transducer Installation Trolling Motor Transducer Installation GPS Receiver Installation If you have… Then useHand-tighten only Follow these steps to stem mount the GPS receiver Access Under Mounting Location Access Under Mounting LocationTo the cable as shown No Access Under Mounting Location Finish Routing the Cable and Check GPS Receiver Operation Install the temperature probe accessory Routing the cable to the control head Testing the System Installation To test the installation Powering UP the Control Head Series 947c 3D Combo Title Screen WHAT’S on the 3D Sonar Display Triplog WHAT’S on the 2D Sonar Display Bait Ball RTS Real Time Sonar Window Real Time Sonar RTS Window Bottom Presentation POWER/LIGHT KEY KEY FunctionsView KEY Menu KEY View Preset Keys WAY Cursor Control KEYExit KEY Info KEY MARK/GOTO KEY ViewsViews available on your 900 Series are Views and Readouts 3D/2D Combo View3D/2D Combo View 2D Sonar View 2D Sonar View 2D Zoom View 2D Zoom View Beam Sonar View BIRD’S EYE ViewBeam Sonar View Bird’s Eye View CHART/BIRD’S EYE Combo View Chart ViewChart/Bird’s Eye Combo View with Active Cursor Chart View with Active Cursor CHART/3D Combo View CHART/2D Combo ViewChart/2D Combo View Chart Orientation Chart View with Cursor PresentViewing Cartography WAYPOINTS, Routes and Tracks NavigationWaypoints, Routes and Tracks SAVE, EDIT, or Delete a Waypoint Chart View with Target Navigate to a Waypoint or PositionADD a Waypoint Target or Trolling Grid Chart View with Grid SAVE, Edit or Delete a Route Save or Clear a Current Track EDIT, Delete or Hide Saved TracksMenu System Sonar Tab, Normal Mode Sonar Tab, Advanced Mode Exit Normal operation by powering your 900 Series off START-UP Options MenuNormal Operation Normal Simulator System Status Self Test Accessory Test GPS Diagnostic View SimulatorSystem Status Self Test Accessory Test GPS Diagnostic ViewAccessory Test Screen GPS Diagnostic View To Adjust Split Screen Position 2D Sonar X-PRESS MenuActive Side Split Position To adjust the Sensitivity To adjust the Upper RangeSensitivity Upper Range Chart Speed Lower RangeBottom Lock To adjust the Bottom Range Bottom Range2D/3D Priority To change the 2D/3D Priority 3D Sonar X-PRESS Menu Highlight Split Position on the 3D Sonar X-Press Menu3D Sonar X-Press Menu Beam Sensitivity 3D Bottom Zoom3D Lower Range Reset 3D View To adjust the 3D HistoryTo Reset 3D View 3D History Highlight Split Position on the Navigation X-Press Menu Navigation X-Press Menu Save Current Track Clear Current TrackSave Current Route Skip Next Waypoint Cancel Navigation Remove TargetRemove Grid Sonar Menu TAB 2D Sonar Colors3D Bottom Style 3D Frame Style 2D Beam Select Fish ID+To change Beam Select To set Fish ID+ To change the Fish ID Sensitivity setting To change the RTS Window settingTo change the Fish ID 3D Reference setting Fish ID Sensitivity Bottom View Zoom WidthKHZ Sensitivity Depth Lines To change the Noise Filter setting To change the Max Depth settingSurface Clutter Noise Filter Temperature Graph Water TypeColor BAR Navigation Menu TAB TracksWaypoints To change the Chart Orientation setting To change the North Reference settingRoutes North Reference Trolling Grid Rotation Trackpoint IntervalTrack MIN Distance MAP Datum Chart Menu TAB Export ALL NAV DataDelete ALL NAV Data To Export All Navigation Data Chart Detail Level MAP BordersLAT/LON Grid Spot Soundings Shaded Depth SET MAP OffsetClear MAP Offset Alarms Menu TAB Depth AlarmFish ID Alarm To change the Depth Alarm setting LOW Battery Alarm Temp AlarmOFF Course Alarm Arrival Alarm Drift AlarmAlarm Tone Setup Menu TAB To change the Units Depth settingTo change the Units Temp setting Units Depth User Mode Units DistanceUnits Speed Language Triplog Reset Restore DefaultsSelect Readouts Default Sonar View Customized Sonar View To Select Readouts Depth Offset Temp OffsetLocal Time Zone Daylight Saving Time Position Format Time FormatDate Format Nmea Output Sonar Views Menu TABTo turn Nmea Output on or off To turn Sonar on or off Accessories Menu TAB TroubleshootingSeries Doesn’t Power Up Series Defaults to Simulator with a Transducer Attached Display Problems Control head loses power at high speeds Finding the Cause of Noise Other electronic devicesNoise re-appears Boat’s engine Year Limited Warranty Humminbird Service Policy Returning Your Unit for Service Series AccessoriesFor IN-WARRANTY service, complete the following steps Specifications Operating Frequency Appendix a Contact Humminbird