Contact Humminbird | Humminbird 531374-1

www531374..reelsche-1 A - 947 Man.qxd 2/15/2005matic7:54..coPM Pagem91

Contact Humminbird®

Contact the Humminbird® Customer Resource Center

in any of the following ways:

By Telephone

(Monday - Friday 8:00 a.m. to 4:30 p.m. Central Standard Time):

1-800-633-1468

By e-mail

(typically we respond to your e-mail within three business days):

custserv@johnsonoutdoors.com

For direct shipping, our address is:

Humminbird®

Service Department

678 Humminbird® Lane

Eufaula, AL 36027 USA

Page 91

Image 91

Humminbird 531374-1_A manual Contact Humminbird

Contents

Page Thank You Table of Contents Navigation X-Press Menu Menu System Start-Up Options Menu2D Sonar X-Press Menu 3D Sonar X-Press Menu Views Menu Tab Accessories Menu Tab Troubleshooting Chart Menu TabAlarms Menu Tab Setup Menu Tab 2D Sonar Series IntroductionHOW the 900 Series Works 3D Sonar MULTI-MEDIA Card MMC SD Slot GPS and CartographySD Slot 900 Series has a wide variety of configurations Accessory BUSInstallation Overview Accessory Bus Basic installation tasks that you must perform include Control Head InstallationGimbal Mounting the Control Head Mounting Screws Washer Gimbal Mounting Bracket Cables Routed Near Mounting Bracket Screws provided Plug Cable Connector Assembly to Back of Control Head IN-DASH Mounting the Control Head Plug Cable Connector Assembly to Back of Control Head Connecting the Control Head Power Cable to the Boat Transducer Installation To determine transducer mounting location Transom Transducer InstallationStepped Hull Attaching the Bracket To mount the transducer bracket to the boatTo attach the pivot to the transducer But do not completely tighten To adjust the running position of the transducer To mount the transducer pivot assembly to the bracketNormal Cavitation Routing the Cable To route the transom transducer cableReassemble Fully tightened Trial installation Inside the Hull Transducer InstallationDetermine the transducer mounting location Transducer Mounted Inside the Hull Permanently mount the transducerRoute the cable Make sure the position of the transducer is marked Trolling Motor Transducer Installation Test and Finish the Transducer Installation Follow these steps to stem mount the GPS receiver GPS Receiver InstallationIf you have… Then use Hand-tighten only Access Under Mounting Location Access Under Mounting LocationTo the cable as shown Finish Routing the Cable and Check GPS Receiver Operation No Access Under Mounting Location Routing the cable to the control head Install the temperature probe accessory To test the installation Testing the System Installation Series 947c 3D Combo Title Screen Powering UP the Control Head Triplog WHAT’S on the 3D Sonar Display Bait Ball RTS Real Time Sonar Window WHAT’S on the 2D Sonar Display Bottom Presentation Real Time Sonar RTS Window Menu KEY POWER/LIGHT KEYKEY Functions View KEY Info KEY View Preset KeysWAY Cursor Control KEY Exit KEY Views MARK/GOTO KEYViews available on your 900 Series are 3D/2D Combo View Views and Readouts3D/2D Combo View 2D Sonar View 2D Sonar View 2D Zoom View 2D Zoom View Bird’s Eye View Beam Sonar ViewBIRD’S EYE View Beam Sonar View Chart View with Active Cursor CHART/BIRD’S EYE Combo ViewChart View Chart/Bird’s Eye Combo View with Active Cursor CHART/2D Combo View CHART/3D Combo ViewChart/2D Combo View Chart View with Cursor Present Chart OrientationViewing Cartography Navigation WAYPOINTS, Routes and TracksWaypoints, Routes and Tracks SAVE, EDIT, or Delete a Waypoint Navigate to a Waypoint or Position Chart View with TargetADD a Waypoint Target or Trolling Grid SAVE, Edit or Delete a Route Chart View with Grid EDIT, Delete or Hide Saved Tracks Save or Clear a Current TrackMenu System Sonar Tab, Advanced Mode Sonar Tab, Normal Mode Normal Simulator System Status Exit Normal operation by powering your 900 Series offSTART-UP Options Menu Normal Operation Self Test Self Test Accessory Test GPS Diagnostic ViewSimulator System Status GPS Diagnostic View Accessory TestGPS Diagnostic View Accessory Test Screen Split Position To Adjust Split Screen Position2D Sonar X-PRESS Menu Active Side Upper Range To adjust the SensitivityTo adjust the Upper Range Sensitivity Lower Range Chart SpeedBottom Lock To change the 2D/3D Priority To adjust the Bottom RangeBottom Range 2D/3D Priority Highlight Split Position on the 3D Sonar X-Press Menu 3D Sonar X-PRESS Menu3D Sonar X-Press Menu 3D Bottom Zoom Beam Sensitivity3D Lower Range 3D History Reset 3D ViewTo adjust the 3D History To Reset 3D View Navigation X-Press Menu Highlight Split Position on the Navigation X-Press Menu Skip Next Waypoint Save Current TrackClear Current Track Save Current Route Remove Target Cancel NavigationRemove Grid 3D Frame Style Sonar Menu TAB2D Sonar Colors 3D Bottom Style To set Fish ID+ 2D Beam SelectFish ID+ To change Beam Select Fish ID Sensitivity To change the Fish ID Sensitivity settingTo change the RTS Window setting To change the Fish ID 3D Reference setting Depth Lines Bottom ViewZoom Width KHZ Sensitivity Noise Filter To change the Noise Filter settingTo change the Max Depth setting Surface Clutter Water Type Temperature GraphColor BAR Tracks Navigation Menu TABWaypoints North Reference To change the Chart Orientation settingTo change the North Reference setting Routes MAP Datum Trolling Grid RotationTrackpoint Interval Track MIN Distance To Export All Navigation Data Chart Menu TABExport ALL NAV Data Delete ALL NAV Data Spot Soundings Chart Detail LevelMAP Borders LAT/LON Grid SET MAP Offset Shaded DepthClear MAP Offset To change the Depth Alarm setting Alarms Menu TABDepth Alarm Fish ID Alarm Temp Alarm LOW Battery AlarmOFF Course Alarm Drift Alarm Arrival AlarmAlarm Tone Units Depth Setup Menu TABTo change the Units Depth setting To change the Units Temp setting Language User ModeUnits Distance Units Speed Restore Defaults Triplog ResetSelect Readouts To Select Readouts Default Sonar View Customized Sonar View Daylight Saving Time Depth OffsetTemp Offset Local Time Zone Nmea Output Position FormatTime Format Date Format To turn Sonar on or off SonarViews Menu TAB To turn Nmea Output on or off Troubleshooting Accessories Menu TABSeries Doesn’t Power Up Series Defaults to Simulator with a Transducer Attached Control head loses power at high speeds Display Problems Boat’s engine Finding the Cause of NoiseOther electronic devices Noise re-appears Humminbird Service Policy Year Limited Warranty Series Accessories Returning Your Unit for ServiceFor IN-WARRANTY service, complete the following steps Operating Frequency Specifications Appendix a Contact Humminbird